Maytag Washer Valve

This water inlet valve regulates the flow of household water into the dishwasher at the start of each cycle. Replacing a weak, clogged, or leaking valve restores proper fill level for reliable performance and helps prevent leaks or fill errors.

• Opens to allow the correct amount of water into the tub; closes to stop the fill
• Common fix for dishwasher not filling or taking too long to fill
• Can resolve low water level that leads to poor cleaning results
• May stop water from seeping into the tub when the dishwasher is off
• Replace if the valve body leaks or the inlet screen is damaged/clogged

• Disconnect power and turn off the dishwasher's water supply before servicing
• Access the valve behind the lower toe/kick panel; place a towel to catch residual water
• Note wire and hose positions and move them to the new valve one-for-one
• Restore water and power, then run a fill to check for leaks and proper operation

This water inlet valve regulates the flow of household water into the dishwasher during each fill. Replacing a worn or clogged valve restores proper filling and consistent wash performance while helping prevent long fill errors. What it does:

• Electrically opens and closes to allow the correct amount of water into the tub.
• Maintains proper water level for wash and rinse phases.
• Common failure symptoms: no water entering, slow/low fill, long fill or "faucet"/fill errors, or leakage from the valve body.
• Internal screen can clog with debris, restricting flow.

• Disconnect power and turn off the water supply before servicing.
• Access the valve near the front/bottom of the dishwasher; place a towel or pan to catch residual water.
• Move wires and water connections one at a time; transfer any mounting hardware or fittings from the original valve as needed.
• Restore water and power, check for leaks, and run a test fill; ensure the float/float switch moves freely.

This water inlet valve assembly regulates when and how much water enters the appliance. Replacing a failing valve restores proper filling or water delivery and helps resolve no-water, slow-fill, or drip-through-the-valve issues.

• Opens and closes to control incoming water flow as commanded by the control system
• Directs water to the appliance's water circuit for proper operation
• Common symptoms: no water entering, weak/slow flow, water seeping in when off
• Physical clues: cracked housing, mineral buildup, or a valve that hums but doesn't pass water

• Disconnect power and shut off the water supply before servicing
• Keep towels handy; relieve line pressure before disconnecting tubing/fittings
• Transfer connectors and any mounting hardware one-for-one; ensure tubing is fully seated and use appropriate thread sealant if your model uses threaded fittings
• Restore water, check all joints for leaks, then restore power and run a test cycle

This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.

• Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
• Helps ensure consistent, unobstructed water flow into the tub
• Replaces a cracked, clogged, or leaking vacuum break at the fill area
• Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill

• Unplug the appliance and shut off both water supplies before servicing
• Access the fill/inlet area; note hose routing and part orientation
• Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
• Restore water and power, then run a fill test and check carefully for leaks

This mixing valve bracket secures the washer's water inlet valve to the cabinet, keeping the valve steady and properly aligned for hose connections. A correct-fit bracket helps reduce rattles and potential leaks caused by a loose valve.

• Mounts and supports the water inlet/mixing valve on the rear panel
• Maintains proper alignment for hot and cold supply connections
• Helps reduce vibration and rattling noises during fill
• Common signs it's needed: loose or dangling valve, misaligned hose connections, or leaks at the valve fittings

• Disconnect power and turn off both water supplies; relieve pressure before removing hoses
• Access the rear of the washer and remove fasteners securing the existing bracket/valve
• Transfer the valve to the new bracket, reusing the original hardware
• Reattach the bracket to the cabinet, reconnect hoses, restore power and water, then check for leaks

This replacement housing is the molded support/cover used in select appliances to secure and protect its mated components. It restores proper alignment and sealing when the original housing is cracked, warped, or has broken mounting tabs. What it does

• Provides a rigid mount and enclosure for the associated component(s)
• Maintains correct alignment and sealing to prevent leaks or air loss
• Protects internal parts from damage and vibration
• Common failure signs: visible cracks, broken tabs, rattling, poor fit, or leakage around the assembly

• Housing

• Disconnect power before servicing; if the part interfaces with water, shut off the water supply
• Note orientation and transfer any screws, clips, seals, or O-rings from the original part
• Inspect mating seals and fittings; replace any worn gaskets to ensure a proper seal
• After reassembly, restore power/water and test for proper operation and any leaks or noise

This water inlet valve regulates the flow of household water into the refrigerator for ice making and dispensing. Replacing a failing valve restores proper fill and helps resolve leaks, low flow, and no-ice/no-dispense issues. What it does:

• Opens and closes to supply water to the ice maker and/or dispenser when energized by the control
• Addresses symptoms like no water at the dispenser, no ice production, slow fill/hollow cubes, or dripping/leaks at the valve area
• Common failures include stuck or leaking valve, clogged screen, or a failed solenoid coil
• Helps eliminate valve buzzing with no fill when the coil is energized but the valve won't open

• 1 water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Keep towels/containers handy; some residual water will drain when lines are removed
• Note and label each tube and wire position; transfer any fittings/brackets from the old valve if applicable
• After installation, restore water and power, check all connections for leaks, and purge air by dispensing water

This water inlet valve controls the flow of household water into the dishwasher at the start of a cycle. Replacing a weak, stuck, or leaking valve restores proper filling performance and helps prevent fill-related errors and leaks. What it does:

• Opens and closes electrically to regulate water entering the dishwasher
• Helps ensure correct fill level and timing for each cycle
• Common failure symptoms: won't fill or slow fill, water seeping into tub when off, external leak at valve connections, loud buzzing/chattering during fill
• May set fill or water supply-related error codes on some models

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Have a towel or shallow pan ready for residual water when removing lines
• Transfer any original mounting hardware or fittings from the old valve as needed
• Inspect/clean the inlet screen and flush the supply line; check all connections for leaks after installation

The Washing Machine Water Inlet Valve is an OEM part for Whirlpool brand washing machines. It regulates water flow into the washer tub during fill cycles and shuts off the supply automatically when the proper water level is reached.

Causes of a bad inlet valve include mineral buildup inside the valve filter restricting flow over time, or mechanical failures of internal plastic parts like diaphragms and seals due to usage stress.

Symptoms of a bad water inlet valve include:

• Slow or inconsistent filling during wash cycles  
• Water failing to shut off fully after the designated fill level  
• An inability to properly meter incoming water supply amounts
• Water leaks noticed beneath or around the valve area

This OEM replacement valve ensures precise water flow regulation. Compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.

This valve controls the flow of household water into the dishwasher during the fill portions of the cycle. Replacing a weak, stuck, or leaking valve restores proper filling and helps prevent fill errors and water damage. What it does:

• Opens and closes to let the correct amount of water into the tub
• Common symptoms: no fill or very slow fill
• Water entering the tub when the dishwasher is off or won't stop filling
• Drips or leaks from the valve body or hose connection

• One water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water; relieve line pressure at the supply
• Note wire and hose orientation before removal; move connections one at a time
• After installation, restore water and power, then run a brief fill to check for leaks

Includes water inlet valve, vacuum break, wire harness and connector hose.

This vacuum break valve (also called a vacuum breaker or anti-siphon valve) prevents dirty water from being drawn back into the supply when flow stops, protecting your water supply and helping maintain proper fill and drain performance.

• Breaks siphon/backflow after fill or drain cycles to prevent contamination
• Helps maintain correct water levels and consistent filling
• Common symptoms of a failed valve: leaks at the valve/hoses, unintended draining or backfilling, intermittent or slow fill, gurgling noises
• Restores the proper water flow path when replaced

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when removing hoses
• Note hose orientation and transfer existing fittings/clamps as needed
• Restore water/power and run a test cycle; check carefully for leaks

This surface burner valve controls gas flow to a cooktop or range burner for smooth ignition and precise flame adjustment. Replacing a worn valve restores reliable lighting and consistent simmer-to-high control at the knob. What it does:

• Regulates and meters gas flow to a surface burner from Off through all heat settings
• Wear or blockage can cause no ignition, hard-to-turn knob, or poor/unstable flame
• Helps correct burners that won't adjust properly or won't stay lit
• Ensures safer, consistent burner performance when operating correctly

• 1 surface burner valve

• Disconnect power and shut off gas supply before servicing; allow appliance to cool
• Work in a well-ventilated area and follow local codes
• Note knob orientation; transfer any orifice fittings or mounting hardware from the old valve
• After installation, check all connections for leaks using a non-corrosive leak-detection solution

New seals come with this valve.

This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.

• Controls incoming water to achieve correct fill levels and temperature mix
• Addresses no fill, slow/partial fill, or water seeping into the tub when off
• Replaces valves that are electrically failed or mechanically clogged/sticking

• Disconnect power and shut off both water supplies before servicing
• Have towels ready; relieve hose pressure and note wire/hose locations (take a photo)
• Transfer any mounting parts from the original valve if required; avoid overtightening plastic fittings
• Restore water slowly, check for leaks, and run a test fill

This valve controls the flow of water into the appliance. When energized, it opens to let the correct amount of water in; when de-energized, it closes to stop flow—restoring proper fill and dependable operation. What it does:

• Opens and closes to regulate incoming water during operation
• Helps maintain correct fill levels for cycles
• Common symptoms of a failing valve: no fill or slow fill, error codes related to water supply, dripping/leaks from the valve area, or humming/clicking with little to no water flow

• 1 valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Label and transfer hoses/wires one at a time; reuse existing hardware/fittings
• Restore water and power, then check all connections for leaks and run a test cycle