Need Help?
Call
Replace a range hood motor that won't spin or runs loud. Restores proper airflow and ventilation. Moderate DIY repair, typically 1-2 hours with cleaning.
Exhausts horizontally to the outside....look at the picture of that beautiful motor.... The hood is nearly 30 years old.. I had replaced the blowers a few years ago and re painted the hood also from white to black to match the oven.... what a beautiful hood matching my beautiful oven !!! ... The motor died ( tears all over the kitchen )... all the other parts were ok so only the $105.00 motor to be replaced ( expensive for a little motor ).... took the motor / blower unit all apart & did a... Read more
Usually ships within 4 - 14 days
Fix a noisy, stalled, or non-starting range hood fan with a new blower motor. Powers the fan blade to move air through your ventilation system.
This is a genuine OEM replacement o-ring sourced directly from the manufacturer for use on range vent hood switches. The o-ring provides a tight seal for the switch and keeps smoke from escaping through the switch connection. If the o-ring becomes worn or damaged, the vent will not remove smoke during cooking and should be replaced. Heat and debris pulled through the vent may cause the o-ring to warp. O-rings are not designed to last forever and may need to be replaced during the life of the appliance to keep it functioning correctly.To start, disconnect the power to the vent hood and dismantle the vent in order to reach the switch. To start, disconnect the switch and locate the o-ring. Remove the old one and dispose of it. Place the new o-ring in the groove and press firmly to seal the part. Lubrication is not necessary for installing the new o-ring. Reassemble the switch and put the vent hood back in place. Connect the power and try the switch to make sure it works. This o-ring is made of heavy-duty black rubber is and sold individually. It is designed for use in range hoods manufactured by Thermidor.
Found replacing the switch to be doable, but it was quite a delicate operation. This was for a Thermador range with a broken downdraft switch. It required the removal of 5 small screws which could easily be fumbled and dropped down where it would be difficult, if not impossible to retrieve. Two of the screws were facing the back, so it was a blind operation to remove and replace the screws. Required an offset screwdriver, as space was tight. So, be EXTREMELY careful to not drop the screws and... Read more
Hood fan making noise or not working? This blower motor assembly powers the fan that circulates air. Simple 3-screw replacement with plug connector.
Replaced the burned-out Blower Motor Assembly. Read more
Captures grease and cooking vapors to keep air fresh and prevent buildup. Replace when clogged or discolored. Verify fit by model number and dimensions.
I ordered replacement filters--the filters fit inside the vent. I did not have a part number, just the model and the size. These fit great! My down draft was installed in 1996, so I was afraid the part might not be available. Success! Read more
This is a metal duct connector plate designed to attach a 7-inch round duct to a range hood vent housing. It provides a secure transition between the hood exhaust outlet and the ductwork, often incorporating a damper function to prevent backdrafts. Replace this plate if you notice air leaking around the duct connection, a rattling noise during operation, or if the existing plate is damaged or corroded.
Captures grease, smoke, and cooking emissions from your range hood. Replace when clogged or discolored to maintain ventilation. Verify dimensions for fit.
I bought the new filters and replaced the old ones Read more
Fix a range hood light or fan that won't turn on or off with this rocker switch. Restores manual control when switches stick or fail to respond.
I ordered the switches from AppliancePartsPros.com and replaced both the light switch and the fan switch. The difficult part of the project is removing the old switches. The collapsible holders on the switches require pressure and maneuvering through the small opening to remove the switches. Problem with original design. The easiest and most satisfying part of the project was the ordering and delivery of the switches. I ordered one day and they were delivered the next day. Both the order... Read more
The Lamp Holder is an OEM part for Bosch range hoods. It secures interior lighting fixtures in place above the stovetop, managing connecting wires neatly out of the way. Proper holder positioning ensures consistent task illumination.
Causes of failure can include normal wear from sustained vibration in the kitchen environment. Periodic replacement preserves essential visibility above the cooktop.
Symptoms of a faulty lamp holder are:
This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
Replaced socket Read more
The Mount, Vibration Rubber Range Hood is an OEM part for Bosch range hoods. It plays a crucial role in mounting the range hood itself and reducing noise and vibrations produced during operation. The rubber vibration mount is designed to absorb shocks and isolate noises, providing a smooth, quiet ventilation experience.
Symptoms of a bad mount can include looseness or detachment of the range hood, increased vibration transfer to surrounding cabinetry, or failure of the rubber material itself.
Symptoms of a bad mount include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore range hood models.
Replaced fan motor, capacitor, & motor mounts Read more
Metal mesh grease filter for range hood. Captures airborne grease and cooking particles to protect the ventilation system. Washable and reusable.
Grease filter for range hoods and over-the-range microwaves. Dimensions: 3-7/8" x 8" x 3/32" (3.875 x 8 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
I removed old filters and installed new ones. Read more
Grease filter for range hoods and over-the-range microwaves. Dimensions: 11-7/8" x 17-11/32" x 3/8" (11.875 x 17.34375 x 0.375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
I ordered the parts on Friday and received them Saturday. Remove & replace Read more
This is a set of three charcoal filters designed for recirculating range hoods that do not vent to the outside. The activated charcoal absorbs cooking odors and smoke as air passes through the filter. Replace these filters every six months or sooner if you notice lingering cooking smells, reduced airflow, or the filters appear visibly dirty or saturated.
Ordered it, received it, placed it in proper place, use the hood! thanks Read more
Captures cooking grease and particles to protect your range hood blower. Replace when clogged to restore airflow and ventilation. Confirm fit by model number.
This is a blower wheel designed for use in a range vent hood. It attaches to the motor shaft and spins to pull air, smoke, and grease-laden vapors up through the hood and out the vent. Replace this part if your vent hood has weak airflow, makes rattling or scraping noises, or the fan vibrates excessively during operation.
Dropped motor assembly down and pulled end off and replaced blower wheel. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.