Refrigerator Parts

I had to purchase the whole glass and support for the drawer and throw out the old glass and everything but the support brackets from the original. Had to remove the support brackets from the original drawer support and install them on the new one. Easy job just a lot of wasted product for a small broken piece. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

Replaced filters Read more

I believe we had two problems. Our gasket was ripped in several places and our drain pan line was clogged. Therefore the water was frozen and backing up into the freezer. Replacing the gasket is an easy job and could possibly be done quickly enough that you don’t have to remove your freezer food items if you don’t discover additional problems during the process. The most time-consuming part is the approximately 40 screws that hold the freezer door shelf panel and gasket to the door itself. ... Read more

I believe we had two problems. Our gasket was ripped in several places and our drain pan line was clogged. Therefore the water was frozen and backing up into the freezer. Replacing the gasket is an easy job and could possibly be done quickly enough that you don’t have to remove your freezer food items if you don’t discover additional problems during the process. The most time-consuming part is the approximately 40 screws that hold the freezer door shelf panel and gasket to the door itself. ... Read more

Ordered a new one. Read more

• Ice maker dispenses too little ice

When I first searched the AppliancePartsPros.com site for my specific model, the ice maker that appeared in the parts list was not for my refrigerator. So, I bought one from one of your competitors. It arrived and worked but produced ice even more slowly than my original unit, albeit at 0F. So, I went back to AppliancePartsPros.com parts list and browsed completely through it only to find another ice maker that did match mine. It was almost twice the cost, but after installing it, worked... Read more

• Fridge too warm

Fan motor went bad. Fixed the fridge for less than it would have cost me just to have someone come out and look at it. Read more

I ordered the replacement part. Your website was the only one I searched which exactly identified the correct part for me to order. The exploded diagram with numbered parts was very helpful. Read more

After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more

Front-wheel attaches to the shelf above. Where it screws in is kind of flimsy, no way to repair, had to replace the entire shelf, including the glass. Appliances Parts Pros had the best price, and it arrived quickly. You have to swap the metal brackets from the old to the new shelf (2 brackets x 5 screws), and reuse the old wheels as well. One thing to note, the holes for the screws and for the wheels are not threaded. The screws cut the threads. Use caution when putting in the screws and... Read more

• Noisy
• Fridge too warm
• Freezer section too warm

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more