Refrigerator Parts

Replaced filters Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

Replaced the valve configuration. It was pretty easy. Read more

• Fridge too warm

Fan motor went bad. Fixed the fridge for less than it would have cost me just to have someone come out and look at it. Read more

After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more

Ordered parts from Appliance Parts Pros. Made sure they fit using the model number link. Was a great experience, fast shipping. Read more

• Ice maker dispenses too much ice

Ice sensing lever (keyed onto mtr shaft) found down and would not budge. Also, test button (hidden beneath mtr) only 'beeped' when pushed. The 10 pin connector's 'clip' is also hidden against roof of freezer - mine broke but connection still seems secure. New unit was exact fit - test button (now) cycles thru one cycle of rotation and H2O fill with no beeps.... 18 hrs later, bin is half full....ice for the summer :) Remove freezer door (front) so you can lay down and look up. Cold plastic... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

I ordered the replacement part. Your website was the only one I searched which exactly identified the correct part for me to order. The exploded diagram with numbered parts was very helpful. Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more

I ordered new parts from your company for my refrigerator. These were easy parts to replace and did not require tools. I was most grateful in being able to order those parts by telephone from your company. This process was surprisingly easy and did not require a long wait to speak to a representative. The persons I spoke with were polite, efficent and very competent. The parts got to me very quickly in well packed boxes. I though this process would be an ordeal and it was the opposite. This was... Read more

• Door latch failure
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

Replaced them and added the shelf / rail Read more

• Doesn't shut off

I only needed the Bracket Assembly motor, not the DC Motor or Fan Assembly that I also ordered so I will be sending those back. The repair was extremely straightforward with a few bumps along the way. All told it took me about an hour. I started with shutting off the breaker for the refrigerator and putting all of the frozen food in coolers. Then I removed the drawers and the bracket for the drawer rails on the left side (as your facing the refrigerator). I then proceeded to gently pry off the... Read more

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more