Refrigerator Parts

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

• Not dispensing water

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

Walk into the kitchen on 21 Sep. Eight year old Frigidaire refrigerator appears to be short cycling, controls are nonfunctional. Unplug it for a few minutes, plug it back in, appears to return to normal function. Return to kitchen half hour 45 minutes later it's short cycling again. Panel has codes on it (S or 5 E CE, later that changes to S or 5 Y CE). Research of codes says replace main board and control board. Not sure where this main board is. 22 Sep call appliance repair. "Soonest... Read more

Installed replacement drawer Read more

In 2012 I purchased an LG French door bottom freezer fridge. this thing was a problem from day one, I had to call 3 technicians where I bought it from- a nameless major retailer. through the 2 1/2 years I have had it, the problems were always with the ice cube maker, and finally, the motor finally stalled. I was able to revive it, but only for a short time- then I went to replace the unit all together and searched high and low until I came across Appliance Pros. I actually had no idea that 2 of... Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

Shut off power in the panel box - easier than getting at the plug behind the unit. Had to take out the lower full-width drawer and the two crispers next. Removed two screws on the shelf above the wide drawer and removed the two shelf parts. Next was removing a screw from each wide drawer support. Then I pulled the support forward about an inch to disengage it from a post towards the back. There is a wiring connection in the right-hand support you will need to disconnect. Next, I removed a... Read more

I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more

I watched the AppliancePartsPros.com video, which made the replacement of an ice maker look pretty easy. The only problem was that my existing wiring harness was affixed to the inside of my refrigerator, whereas in the video, the existing cord was shown as readily disconnectable, so I was unsure how to proceed. Then I saw a comment by another user, expressing the same issue. The AppliancePartsPros representative advised the consumer simply to retain and use the existing, affixed wiring... Read more

• Freezer not defrosting
• Too warm
• Fridge too warm
• Freezer section too warm

I ordered a freezer temperature control. I ordered from you because parts are certified. Last thing I wanted was to go through the replacement process with a part that didn’t work. I’m not a handy person by nature, and I have zero common sense. I watched the awesome instructional video that you provided with my order several times. Before receiving or even opening the package, I felt that I knew what to expect because I watched the video so many times. Before beginning, I made sure I had as... Read more

I ordered a replacement bin, and since the price was reasonable I ordered a second one to help with organization in my refrigerator. I thought it would be a week for the bins to arrive, but it only took three days(one of those was a Sunday). Read more

• Ice maker dispenses too much ice

I replaced the ice maker after replacing the ice try and before that the ice chute gasket. All easy fixes. However, I am still seeing some frost build-up leading me to believe that the issue is just a faulty design, which I have read other posts on. Just too much warm air gets in the ice maker because it is located in the refrigerator, plus warm air probably finds its way from the outside dispenser, up the chute into the ice maker. Oh well, nothing the occasional hair dryer won't take care of,... Read more

Replaced the seals Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

• Ice maker dispenses too little ice
• Ice maker dispenses too much ice
• Ice maker won't dispense ice
• Ice maker not making ice

Replace assembly Read more

Replaced it with a new one Read more