Roper Parts

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

• Door won't close

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

• Not dispensing water

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

• Freezer section too warm
• Fridge too warm

Replaced the heater, timer, and wiring harness Read more

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

Didn't have to -- you had a compatible product and sent it to us. Read more

I could not find specific online instructions for this job. Here are some tips. 1. Unplug the washer. 2. Unscrew the dial on the broken timer. 3. Gently pry up the thin plastic place-indicator plate (the thing with the arrow under the dial) with two flathead screwdrivers. 4. Unscrew the two hex screws holding the old timer in place. 5. Unscrew the phillips-head screws holding the console in place and flip up the console. 6. Remove the electrical connector from the bad timer, and remove the bad... Read more

Bot both sets of roller bearings, lower ones on the appliance and the set on the trash can that rolls out. I just followed the instructions that were in the roller bearing package and only needed the tools that are recommended. Was a little tricky with the nuts, really need a person with "small" fingers to reassemble the nuts back on the lower set of bearing that are on the appliance. All in All, went well and works. Found that the new bearings are v. tight on the machine, being new, so, use... Read more

Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more

Replaced pump Read more

• Fridge too cold

Easy fix in less than 10 minutes. I replaced the thermostat control. I first shorted the two wires that went to the control and let it run for 1 hour. The temperature was dropping and the freezer was freezing. Read more

• Freezer not defrosting
• Fridge too warm

Defrost circuit was broken, defrost thermostat failed and allowed the frost to build up and clog the ports . Replaced defrost thermostat and fixed the circuit.....the heating element worked again as the defrost thermostat was broken in the open position, not allowing the heating element to operate. Read more

• Will not fill with water

I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new... Read more

Fast delivery, great service Read more

I diagnosed the problem, identified faulty parts, and replaced those components. Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more