Washer Panel Parts

Replacement lid for Speed Queen washers. Covers the washing drum and provides access for loading clothes. Replace if rusted, cracked, or has sharp edges.

Replacement outer door panel for washer front-load doors. Installs around door glass. Replace if cracked at hinge, broken from impact, or warped plastic.

Control panel housing assembly for washing machines. Includes console case, trim, wiring harness, and mounting components. Replaces cracked or damaged panels.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rear access cover panel for refrigerators. Shields compressor and electrical components from dust and debris. Replace if cracked, damaged, or worn.

Rear console housing for washer controls. Supports and protects user interface components. Replace when original panel is cracked, loose, or damaged.

Replace your worn, cracked, or broken washer control panel. Houses buttons, dials, and display for setting selections. Essential when panel is damaged or detached.

This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:

• Provides a complete, aligned door to open/close the cavity smoothly
• Ensures latch hooks engage properly so the appliance can operate
• Replaces doors that are cracked, warped, or have broken handle mounts
• Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
• Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen

• One door assembly

• Disconnect power at the breaker before servicing; microwaves contain high-voltage components
• For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
• Transfer any reusable hardware/hinge pins/trim from the original door as needed
• Align the hinges and verify the door closes, latches, and opens smoothly before remounting

This replacement top panel restores the appliance's upper surface and protects internal components while giving a clean, finished appearance. Ideal when the factory top is dented, rusted, or otherwise damaged. What it does:

• Covers and protects internal components located beneath the top panel
• Provides a flat, finished surface for user access and controls
• Restores proper alignment and fit where the original top is bent or corroded
• Helps stop drafts, debris, or moisture from entering the cabinet area

• One top panel

• Disconnect power (and gas, if applicable) before starting any repair
• Handle edges carefully; use gloves to avoid cuts
• Reuse mounting hardware only if in good condition; replace damaged fasteners

Exterior upper cover panel for washers. Restores a finished look and protects internal components. Replace if cracked, dented, or damaged from impact.

This trim ring is a replacement surface trim piece that restores the finished look and edge around the appliance opening. It provides a clean, secure edge and replaces bent, cracked, or missing trim to improve appearance and fit. What it does

• Covers and finishes the exposed edge of the appliance opening for a clean appearance
• Secures and aligns adjacent components by providing a stable mounting edge
• Addresses cosmetic damage such as dents, cracks, or paint loss around the opening
• Helps prevent small items from getting caught in the exposed edge

• One trim ring

• Disconnect power to the appliance before starting any repair
• Removal typically requires loosening mounting screws or clips; keep hardware for re-use unless damaged
• Handle edges carefully; part and surrounding metal may be sharp
• If the trim mounts to or around other components (elements, panels), support those parts during removal and reinstallation

Galvanized steel top panel that covers and protects internal washer components. Replace if your original panel is rusted, dented, or corroded.

Replace your washer's top plate assembly if cracked, broken, or damaged. This structural panel secures and covers the upper cabinet area. Direct fit.

Top plate assembly for washers. Mounts to the back of the machine and covers the top panel area. Replace if cracked, broken, or missing screws.