Parts for Lg WM2233HS / ATTEEUS: Section 2 Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a plastic lifter baffle that mounts inside the dryer drum. It tumbles and lifts clothes as the drum rotates, promoting even airflow and efficient drying. Replace this part if it is cracked, broken, or missing, which can result in clothes bunching together, uneven drying, or loud thumping noises during operation.

Central hub that connects the inner tub to the drive shaft in washers. Replace if corroded, cracked, or arms have broken off causing wobble or imbalance.

Supports the inner drum for smooth rotation during wash and spin cycles. Replace when you hear grinding, loud noise, or excessive vibration. Confirm fit with your model number.

Supports smooth drum rotation in your washer. Replace if you hear loud roaring or grinding noises during spin cycles. Confirm fit with your model number.

Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.

Seals between inner and outer tubs to prevent water leaks during wash cycles. Replace if you notice leaks or after bearing replacement. Verify fit.

Fix excessive washer vibration and loud spinning with a new balance weight. Stabilizes the tub during spin cycles. Moderate DIY repair for most models.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

Concrete balance weight mounts to washer outer tub to stabilize drum during spin. Replace if cracked, broken, or missing to restore proper vibration control.

The Motor Wiring Harness is an OEM replacement part for LG washing machines. It is responsible for supplying power from the washer control board to the motor and related components. The wiring harness conducts electrical current, allowing for the operation of the pump, motor, and other vital systems. 

Causes of a bad motor wiring harness can include damage due to repetitive use and wear over long periods of time, exposure to moisture, impact or abrasion damage, or faulty insulation leading to electrical shorts.

Symptoms of a bad motor wiring harness include: 

• The washer failing to start or functioning intermittently
• Strange noises coming from the motor or other electrical components
• Slow or ineffective spinning or agitation  
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore washing machines. 

The Washer Gasket is an OEM replacement part for LG washing machines. It is a flexible seal that lines the opening of the washer tub, creating an airtight barrier to prevent water leaks and ensure proper containment during the wash and spin cycles.

Symptoms of a bad washer gasket include:

• Water leaking from the front of the washing machine
• Excessive moisture or condensation buildup around the gasket area
• Difficulty in properly closing and latching the washer door due to a worn or damaged gasket

Causes of a washer gasket failure can range from general wear and tear over time, to physical damage from being pinched or cracked, to improper installation or alignment issues.

This OEM LG part is also compatible with Sears/Kenmore models.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Connects detergent dispenser to washer tub. Replace if cracked, leaking, or clogged with detergent buildup. Verify fit with your model number.

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

Includes sensor probe

Washer won't drain or shows OE error? This drain pump assembly removes water during spin cycle. Moderate DIY repair with video guide available.

Note: Per the manufacturer, the design changed  of this washer drain pump changed in April 2025. The new gray casing with different fins will still work, as the fins allow access for wiring.

Drain hose carries used water from washer to household drain. Replace if cracked, leaking, deteriorated, or damaged to prevent water overflow issues.

The Pump Casing is an OEM replacement part for LG washing machines. It is a crucial component that houses the drain pump, which is responsible for removing water from the wash tub during the drain and spin cycles.

Symptoms of a need to replace the pump casing:

• Leaks or water seeping from the pump area
• Unusual noises or vibrations during the drain or spin cycles
• Pump failure or inability to drain water effectively
• Cracks or damage to the casing itself

Causes of a faulty pump casing can include physical impact or mishandling, excessive wear and tear over time, or potential manufacturing defects.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

Water leaking from filter area or drain error? This washer pump filter traps lint and debris. Easy DIY fix with video guide—most install in minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This front load washer drive motor stator includes the rotor position sensor switch (RPS). For the RPS switch only order 6501KW2002B.

Fix LE error codes and spinning problems with this washer rotor position sensor. Resolves machines that won't spin or make loud noises. Easy 5-10 minute fix.

Fix grinding noises or a drum that won't spin with this washer motor rotor assembly. Common when spline teeth strip. Moderately difficult repair.

Replacement suspension spring for washer tub support. Installs between cabinet and tub to absorb vibration. Replace if broken, stretched, or missing.

Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Replace your washer door seal gasket if you notice water leaks, mold buildup, or odors. Creates watertight seal between door and drum. Verify fit.

For the gasket without the drain hole order part 4986ER0004B.

Replacement tub to pump hose for washers. Transports water from the wash tub to the drain pump. Replace if cracked, split, leaking, or damaged from wear.

Secures the inner door gasket to prevent water leaks during wash cycles. Replace if gasket is loose or leaking. Confirm fit with your model number.

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.

Replace your washer's drain hose if cracked, leaking, or damaged. Connects the pump to the standpipe for proper water drainage during wash cycles.

Joins two internal water lines in your washer. Replace this coupler if cracked, worn, or leaking to restore a secure connection during fill and wash cycles.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Shock absorber kit reduces vibrations and stabilizes the drum during wash cycles. Replace if worn, leaking, or causing excessive movement and noise.

Locking pin for shock absorber.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.