Washer Dryer Combo Cap Or Cover

This replacement cap covers an opening or fastener on the appliance. It helps keep water, detergent, and debris out while restoring a clean, finished look and maintaining a secure fit. What it does:

• Covers and protects an exposed opening or fastener from moisture and debris
• Helps prevent residue from entering internal areas
• Restores the appliance's finished appearance
• Common signs of failure: missing cap, cracks, warping, or a cap that won't stay seated

• 1 cap

• Unplug the appliance; if working near water connections, turn off the water supply
• Carefully remove the old cap without prying against delicate surfaces
• Clean the mating area; align and press or twist the new cap until fully seated
• Verify a secure fit and normal operation

This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.

• Covers and insulates the fuse terminals to protect the connection
• Helps prevent accidental contact, arcing, and debris intrusion at the fuse
• Common signs you need this part: missing cover, cracks, heat discoloration, or a cover that won't stay secured
• Promotes a secure, consistent fuse connection once installed

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the fuse area per your service information; note wiring and cover orientation
• Remove the damaged cover; inspect terminals and wiring for heat damage or looseness
• Seat the new cover fully and verify it is secure and clear of wiring

This replacement cover fits the washer's front service door. It restores a clean, finished look and helps shield the service compartment from dust and debris when the original cover is cracked, loose, or missing.

• Covers the service opening to protect internal components from debris and accidental contact
• Restores cabinet appearance by concealing the service area
• Replaces a broken, warped, loose, or missing cover
• Common symptoms: cover won't stay closed, visible cracks, rattling, or a missing access cover

• Disconnect power and turn off water before servicing
• Remove the damaged cover
• Align the new cover with the existing hinge/tabs and secure per your model's configuration
• Confirm proper closure and clearance before restoring power

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

This cover protects the appliance's fuse and terminal area, keeping electrical connections insulated and reducing the risk of shorting or arcing. A simple replacement restores the protective barrier over the fuse compartment. What it does:

• Shields the fuse and terminal block from debris and accidental contact
• Helps prevent electrical shorts or arcing at the fuse/terminal area
• Keeps the fuse securely positioned in its holder
• Restores the appliance's intended insulation and safety for the electrical connection

• One fuse terminal cover

• Disconnect all power to the appliance before accessing the fuse or terminal area
• Remove any mounting screws or clips holding the old cover; replace with the new cover in the same orientation
• Inspect the fuse and terminal connections for damage before reassembly; replace any damaged components as needed
• Do not operate the appliance with the fuse or terminals exposed

A small replacement clip cover that restores the finished look and secures trim or small components on your appliance. It protects edges and helps keep panels and trim pieces held firmly in place. What it does:

• Snaps over a mounting clip or trim edge to conceal hardware and restore appearance
• Helps prevent trim pieces from rattling or coming loose
• Covers exposed clip ends to reduce sharp edges and snags
• Maintains a clean, finished fit where trim meets the appliance cabinet

• Disconnect power to the appliance before beginning any repair
• Typically installs by snapping onto the existing clip or trim edge; no special tools usually required
• Inspect the underlying clip or bracket for damage and replace if worn before installing the cover
• Handle gently to avoid cracking the plastic; replace if brittle or broken

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

This replacement cover restores the appliance's exterior finish while protecting internal components from dust and debris. It fits into the cabinet opening to secure and conceal underlying parts for safe, clean operation. What it does:

• Protects internal components and wiring from dust, lint, and accidental contact
• Restores a finished appearance when a panel is cracked, warped, or missing
• Prevents small items from falling into the appliance cavity
• Reduces rattling from loose or missing panels

• One replacement cover

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools (screwdriver) may be required to remove fasteners or retainers
• Align tabs or slots, then secure fasteners without overtightening to avoid cracking

A left-side hinge washer cover that restores the washer lid hinge's appearance and helps protect the hinge assembly from dirt and wear. Fits where the hinge meets the cabinet to keep the hinge area covered and tidy. What it does:

• Covers and protects the left lid hinge area from debris and abrasion
• Helps prevent direct metal-to-metal contact that can accelerate wear
• Restores finished appearance after a cracked or missing cover
• Can reduce rubbing noises caused by an exposed hinge

• Disconnect power to the appliance before servicing to avoid injury
• Usually installs by snapping or securing over the left hinge; remove hinge fasteners only if necessary
• Inspect hinge and surrounding parts for damage before reassembly
• Do not force plastic parts into place; replace if cracked or deformed

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This manifold cover protects the appliance manifold assembly by shielding valves and fittings from dust, debris, and accidental contact. It restores a secure, finished appearance and helps keep manifold components functioning reliably. What it does:

• Shields manifold valves, fittings and connections from dust, food particles and spills
• Helps prevent accidental snagging or contact with manifold components during use or maintenance
• Restores a damaged, cracked or missing cover to maintain a finished appearance
• Can reduce intrusion of debris that complicates service or repairs

• Disconnect power and shut off gas supply before starting work
• Replace only with the correct OEM part and align over manifold before fastening
• Use appropriate fasteners; do not overtighten to avoid cracking the cover