Washer Dryer Combo Door, Door Glass & Parts

This lid washer cushions and spaces the washer lid hinge so the lid opens and closes smoothly and reduces wear. It helps restore proper lid alignment and quiet operation on compatible top-load washer models. What it does:

• Provides a bearing surface at the lid hinge to prevent metal-on-metal contact
• Reduces lid wobble, scraping, or grinding noises during opening and closing
• Helps maintain correct lid spacing and alignment for secure closing
• Prevents premature wear of hinge components by absorbing friction

• One lid washer

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Access the lid hinge per your model's service instructions; remove hinge fasteners to replace the washer
• Handle small parts carefully and keep track of any related clips or screws

This genuine OEM part is a washer lid. The washer lid is the main piece that covers the washer. Over time, a washer lid can become damaged to the point where it no longer closes securely. If the washer lid is no longer closing all the way or is severely cracked or damaged, it will need to be replaced.To replace this part, start by making sure the washer is unplugged. After it has been powered off, proceed to take a putty knife to lift to release the two retaining clips that secure the washer's main top. Once released, proceed to remove the lid lock assembly wire connector. Fully remove the main top and set it upside down. Release the tension on the lid springs and detach the springs from the main top and hinge bars. Using a Phillips head screwdriver, remove the screws that secure the hinge bars to the lid. Push the hinge bars through the bearings then twist the bars to remove them. This will separate the lid from the main top. Take the new lid and align it with the main top. Insert the hinge bar between the main top and bearing while threading the screws to secure the new top. Reinstall the top panel and connect the wire harness. This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This is a complete microwave oven door assembly that restores a damaged or non-sealing door so the oven operates safely and retains heat. Use it to replace a cracked, bent, or otherwise compromised door assembly. What it does

• Replaces the full door structure including the frame and glass panel so the microwave can close and seal properly.
• Restores proper door alignment and latch engagement when the door is bent or won't stay closed.
• Prevents heat and steam from escaping through damaged seals or cracked glass.
• Helps restore normal operation when the oven won't run due to a door that fails to close securely.

• Disconnect power to the appliance before starting any repair.
• Handle glass and the assembled door carefully; use gloves and eye protection to avoid cuts.
• Align hinges and engage the latch fully when mounting; test door operation before use.
• If the door is heavy or awkward, have a second person assist to avoid dropping or damaging the part.

This complete microwave oven door assembly replaces a damaged or non-sealing outer door to restore safe operation and visible access to the cooking cavity. Fits as a factory-style replacement for compatible GE countertop and over-the-range microwaves. What it does:

• Replaces cracked, dented, or warped outer door panels that prevent proper closing or latching
• Restores a secure door seal so the oven can start and operate normally
• Provides a clear viewing window for monitoring food without opening the door
• Helps stop rattling or loose door movement caused by bent hinges or mounts

• Disconnect power at the breaker and unplug the appliance before starting any repair
• Handle the glass and trim carefully to avoid breakage or injury
• Verify door latch and hinge alignment during installation; small adjustments may be required

This outer refrigerator door replaces a damaged or worn exterior door panel so your fridge seals and looks like new. It restores proper closure and helps maintain internal temperature control and appliance appearance. What it does:

• Replaces a damaged, dented or cracked outer refrigerator door panel
• Restores a straight, secure door edge for better sealing and operation
• Helps prevent cold air loss that can cause temperature fluctuations
• Improves appliance appearance by replacing scratched or faded exterior finish

• One outer refrigerator door panel

• Disconnect power and empty the door before starting; remove any screws or hinge covers securing the door
• Lift or support the door while removing hinge fasteners to avoid dropping or damaging the cabinet
• Align hinges and test door swing and seal before tightening all fasteners
• If inner components (bins, trim, gaskets) are attached, they should be properly reinstalled or transferred per manufacturer instructions.