Washer Dryer Combo Axle, Roller, Pulley Parts

The Dryer Rear Drum Support Roller Kit is an OEM replacement part for  Whirlpool dryers, as well as Kenmore, Samsung and other brands. This kit includes the rear support rollers that are crucial for maintaining proper drum alignment and smooth rotation during the drying cycle. Matching belt 341241 and idler pulley WP691366.

Symptoms of a faulty Rear Drum Support Roller Kit include:

• Excessive vibration or shaking during drying cycles
• Loud grinding or squeaking noises from the rear of the dryer
• Uneven wear or visible damage to the rollers
• Potential drum misalignment, rubbing against the drum casing, or leaks

Causes of a bad Rear Drum Support Roller Kit can include wear and tear over time, excessive load imbalances, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models. 

The Drum Support Roller is an OEM replacement part for Whirlpool dryers that is responsible for supporting the drum and allowing it to rotate smoothly. Causes of a bad Drum Support Roller can include lint and debris that accumulates and causes the rollers to malfunction or seize.

Causes of bad Drum Support Rollers can include wear and tear over time, excessive load imbalances, or physical damage from impact or mishandling.

Symptoms of a bad Drum Support Roller include:

• Unusual noises, such as thumping or squealing.
• The dryer drum struggling to rotate or not turning smoothly.
• Increased vibration or shaking of the dryer during operation.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Idler Pulley is an OEM replacement part for Whirlpool dryers. This essential component plays a crucial role in the drum drive system, helping to guide and maintain proper tension on the dryer belt.

Causes of a faulty idler pulley in a dryer can include normal wear and tear over time, improper belt tensioning leading to bearing failure, or physical damage from impact or debris buildup.

Symptoms of needing to replace the idler pulley include:

• Squeaking or grinding noises from the driveability area
• The dryer drum not spinning or rotating properly
• Excessive vibration or shaking during the dryer cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models. 

The Idler Arm Assembly is an OEM part for Frigidaire dryers. It is an essential component of the dryer's drum support system, responsible for maintaining the proper alignment and smooth rotation of the drum during operation. The idler arm assembly typically consists of an idler arm, pulley, and bearings, working together to support the weight of the drum and facilitate its rotational movement.

Symptoms of a bad idler arm assembly in a dryer include:

• Loud squeaking or grinding noises during operation
• Excessive vibration or shaking of the dryer
• Difficulty in starting or maintaining the drum's rotation
• Potential damage to other components due to misalignment

Causes of a bad idler arm assembly can include wear and tear over time, damage from foreign objects entering the drum, or issues with the bearings or pulley components. A faulty idler arm assembly can lead to improper drum alignment, increased friction, and potential damage to other parts of the dryer.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.

Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact. 

Symptoms of a bad motor mount, roller, or spring include:

• Excessive noise during the wash or spin cycle
• Vibrations or shaking of the washing machine
• The drum not spinning properly
• Motor misalignment or poor performance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This pulley set screw secures the washer's drive pulley to its shaft. Replacing a stripped or missing fastener restores a solid pulley connection to help prevent belt slippage, noise, and spin or agitation issues. What it does:

• Locks the pulley to the shaft to prevent sliding or wobbling
• Helps maintain belt alignment and power transfer
• Can help when the pulley feels loose, the belt squeals or slips, or spin/agitation is weak or intermittent
• Replaces a damaged, stripped, or missing pulley set screw

• 1 set screw

• Disconnect power and turn off water before servicing
• Access the drive system; remove the belt if needed to reach the pulley
• Align the pulley with the flat on the shaft, then install and tighten the set screw with the correct hex/Allen key—do not overtighten
• Reassemble and test

This transmission pulley mounts on the washer's transmission shaft and is driven by the belt to power agitation and spin. Replacing a worn pulley restores smooth belt tracking, reduces noise, and helps the tub move correctly.

• Mounts on the transmission shaft and transfers motor power through the drive belt
• Enables proper tub movement during agitate and spin cycles
• Wear or damage can cause squealing or grinding noises, or a burning rubber smell
• May lead to poor/no spin or agitation, or the drive belt slipping off

• Disconnect power and wear gloves; safely tip or raise the washer for bottom access
• Remove the drive belt, then the pulley's retaining hardware; install the new pulley and secure hardware
• Reinstall the belt with correct routing; replace a worn belt at the same time
• Spin the pulley by hand to ensure free movement and alignment before testing

The Idler Arm Assembly is an OEM component specifically designed for GE dryers. It is a vital part that helps transfer power from the motor to the tumbling action of the dryer drum. The idler arm assembly allows the belt to provide smooth, consistent power to operate the drum efficiently during each cycle.  

Symptoms of a bad idler arm assembly include:

• Squealing or grinding noises coming from the dryer motor or drum area
• The dryer drum not rotating or spinning slowly
• Loose, cracked, or worn idler pulley
• A worn or slipping dryer belt 

Causes of failure can be normal wear and tear over extended use. Excess vibration from an unbalanced load or a dropped object inside the dryer could also potentially damage the idler arm.

This part is compatible with Hotpoint, RCA, and Kenmore dryer models.

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

This V-pulley guides and supports the dryer drive belt so the drum turns smoothly and quietly. Replacing a worn pulley restores proper belt tracking and reduces noise or slipping during operation. What it does:

• Guides the dryer drive belt and helps maintain correct belt alignment
• Reduces belt wear and prevents slipping that can stop the drum from turning
• Helps eliminate squealing or grinding noises caused by a worn pulley bearing
• Restores smooth, reliable drum rotation when installed with a good belt

• One V-pulley

• Disconnect power (unplug electric or shut off gas and disconnect power) before servicing
• Requires basic hand tools and access to the dryer front or rear panel
• Inspect the drive belt and mounting hardware; replace any worn components for best results
• Follow OEM instructions and safety guidelines; do not force parts or overtighten fasteners