Washer Dryer Combo Shaft Or Pin

The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.

The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.

Symptoms of a failing Rear Drum Support Shaft include:

• Unusual noises, such as thumping or squeaking, during operation
• The dryer drum struggling to rotate or not rotating at all
• Increased wear on other components, such as the belt or motor, due to improper drum alignment

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

For complete bearing kit order WE25X10001.

This front suspension rod assembly supports and stabilizes the washer tub from the front of the cabinet. Replacing a worn rod helps reduce vibration, banging, and out-of-balance movement so the washer operates more smoothly.

• Supports and balances the tub from the front corner of the cabinet
• Damps vibration and side-to-side movement during wash and spin
• Helps address symptoms like excessive shaking, banging, or the tub leaning forward
• Reduces walking, rattling, or frequent out-of-balance interruptions

• Disconnect power and water; wear gloves and eye protection
• Support the tub before removing the rod—spring is under tension
• Replace one rod at a time and match the upper/lower end orientation
• Ensure both ends are fully seated in their sockets; re-level the washer after reassembly

A small locating pin used to align and secure parts during assembly, helping panels and components sit correctly for reliable operation. Ideal when a worn or missing pin causes fit or alignment issues. What it does:

• Positions and holds panels, trim, or assemblies in the correct location during reassembly
• Prevents shifting or misalignment of covers and access panels
• Restores proper fit where a bent, broken or missing pin causes loose trim or gaps
• Small, simple replacement that addresses common fit/fitment symptoms

• Disconnect power and unplug the appliance before beginning any work
• Use basic hand tools; avoid forcing parts into place to prevent damage
• Inspect surrounding components for damage and replace if worn

For a complete drum bearing and shaft kit order 5303281153.

This cap stud is a small protective cover that helps secure and shield electrical or mechanical studs on appliances, reducing debris buildup and protecting connections. It provides a simple, low-cost way to maintain safe appliance operation. What it does:

• Covers and protects exposed studs or fasteners from dirt and moisture
• Helps prevent accidental contact with terminals or sharp edges
• Keeps mounting hardware in place for a neater appearance
• Can reduce corrosion risk at exposed connection points

• One cap stud

• Inspect the stud and surrounding area for damage before installing
• Push the cap onto the stud until it seats firmly; no special tools typically required
• Disconnect power to the appliance before working near electrical connections
• Replace if damaged, cracked, or loose to ensure continued protection

A coiled roll pin used to secure shafts, rollers, or linked components in place, helping maintain proper alignment and smooth operation. Ideal when a worn or damaged pin allows movement or causes noisy parts. What it does:

• Secures shafts, rollers, or pivots by fitting into a mating hole to prevent axial movement
• Keeps rollers and linked components aligned for smooth rotation and operation
• Common symptom: loose or wobbling roller/shaft or parts that shift during use
• Common symptom: unusual noise or intermittent binding where a pin retains a component

• Disconnect power to the appliance before beginning any work
• Removal/installation may require a punch and hammer or pliers; protect surrounding surfaces
• Replace with the exact part number to ensure correct fit and retention
• Keep small parts away from children and pets

A replacement pin alignment used to correctly position and secure moving parts in appliance hinge or latch assemblies. Restores proper alignment to reduce sagging, rubbing, or uneven operation for smoother, quieter performance. What it does:

• Aligns and secures hinge or latch components to maintain correct movement and fit
• Helps stop door sag, binding, or uneven closing when the alignment pin is worn or damaged
• Reduces rubbing and noise caused by misaligned parts
• Restores proper clearance for seals and moving assemblies

• One pin alignment

• Refer to the appliance OEM service manual for model-specific removal and installation steps
• Disconnect power (or unplug) and, if applicable, remove stored contents before working on doors or hinges
• Use basic hand tools; avoid forcing parts or over-tightening fasteners to prevent damage
• If alignment issues persist after replacement, inspect associated hinges, brackets, and fasteners for wear