Washer Dryer Combo Tub Ring Or Cover, Counterweight

Note: Newly designed cover includes 4 new rod and spring assemblies. The tub dampening straps and clips are no longer used.

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

This tub ring mounts to the top of the washer's outer tub to act as a splash guard and cover. Replacing a cracked or loose ring helps contain wash water and helps prevent leaks or debris from the top. What it does:

• Forms the upper splash guard around the outer tub to keep water contained during wash and spin
• Serves as the top cover at the tub opening, locking in with tabs/clips
• Damage (cracks, broken tabs) may lead to leaks from the top, rattling, or a loose ring
• Visible wear can leave plastic fragments in the basket or around the tub opening

• 1 tub ring

• Disconnect power and turn off water supplies before servicing
• Lift or remove the top/console per model design to access the tub opening; support the lid
• Release the locking tabs/clips and remove the old ring; clean the tub lip
• Align and press the new ring evenly until all tabs fully engage; reassemble and test

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

Restore a proper seal at the top of your washer's tub with this tub cover assembly. It contains water and suds, reduces splashing, and provides a smooth rim to protect garments during wash and spin. Also called a tub ring.

• Seals the top of the outer tub to keep water and suds contained during operation
• Provides a smooth basket opening to help prevent fabric snagging
• Helps maintain stable operation; a cracked or loose cover can rub, vibrate, or leak
• Common symptoms: water or suds at the top of the tub, excessive splashing, visible cracks or broken tabs

• Disconnect power and turn off water supply before servicing
• Lift/remove the washer top to access the tub area; release clips/fasteners holding the old cover
• Clean the tub lip and transfer any reusable components from the old cover if applicable
• Seat the new cover evenly and secure all tabs/clamps; run a leak check

For seal only use part number 131901400.

This replacement balance weight helps stabilize the washer tub during spin cycles to reduce excessive shaking and banging. Restores proper weight distribution so the washer runs more quietly and completes cycles without heavy vibration. What it does:

• Adds counterweight to the washer tub to help balance loads during spin.
• Reduces shaking, banging, and excessive movement during high-speed spins.
• Can help prevent intermittent off-balance conditions and noisy operation.
• Works as a direct replacement for worn, cracked, or missing tub weights.

• Disconnect power and turn off water supply before beginning any repairs.
• Access may require removing the washer cabinet or front panel; follow the model-specific service manual.
• Wear gloves and eye protection; use appropriate tools and fasteners to secure the weight.

Washer tub ring that snaps onto the top of the outer tub. It acts as the tub cover and splash guard, guiding water back into the tub and supporting inlet or dispenser fittings to help keep the rim area contained.

• Attaches to the top of the outer tub as the upper splash guard/tub cover
• Directs water back into the tub; supports inlet/dispenser nozzles, if equipped
• Maintains proper clearance around the spin basket
• Common replacement signs: cracks, broken locking tabs, splashing from the rim, or rubbing at the top opening

What's included: 1 tub ring Install notes:

• Disconnect power and water supplies before servicing
• Lift or remove the top panel to access the tub rim
• Release locking tabs and detach any hoses/nozzles from the old ring; transfer fittings if needed
• Seat the new ring evenly; ensure all tabs fully engage. Reassemble and run a test cycle to check for leaks/splashing