Washer Dryer Combo Gearcase Parts

The Transmission is an OEM part for Whirlpool washing machines. This integral component is at the heart of the washing machine's operation, translating the motor's power into action by driving the agitator and spinning the drum. 

Regular inspection and maintenance can prolong the life of the transmission, but if these symptoms occur, it may be time to replace this critical component. 

Symptoms of a bad Transmission include:

• The washing machine making unusual noises during the wash or spin cycles, such as grinding or whining sounds.
• The washer failing to agitate properly, affecting the cleanliness of the laundry.
• The drum not spinning during the spin cycle, leaving clothes wetter than usual.
• Leakage of transmission fluid beneath the washing machine.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Neutral Drain Kit is an OEM part for Whirlpool washing machines. This kit facilitates the neutral drain function, which allows the washer to drain water without spinning the tub, ensuring efficient water removal before the spin cycle begins.

Causes of a bad neutral drain kit can include wear and tear over time, mechanical failure of the components, or damage due to improper installation or handling. A faulty neutral drain kit can lead to draining issues, affecting the overall performance of the washing machine.

Symptoms of a bad neutral drain kit include:

• Washer not draining properly
• Extended or incomplete drain cycles
• Water remaining in the tub after the drain cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This gearcase assembly transfers motor motion to the dishwasher's wash components so spray arms and wash mechanisms turn smoothly for consistent cleaning performance. Durable housing aligns gears and bearings for reliable operation. What it does:

• Transfers drive from the motor to the spray arms and wash assembly
• Houses gears and bearings that control rotation and torque
• Helps restore normal spray-arm rotation and wash action
• Commonly replaced when rotation is sluggish, noisy, or intermittent
• Can reduce grinding noises or irregular wash performance when faulty

• Disconnect power (and water, if applicable) before beginning repair
• Remove access panels and other components as shown in your service manual
• Inspect surrounding seals and fasteners; replace damaged parts as needed

This transmission assembly drives the agitation and spin cycles by transferring motor power to the tub. Replacing a worn transmission helps restore proper wash action and spin performance.

• Converts motor rotation into the geared motion needed for wash (agitate) and spin
• Shifts between agitation and spin modes during the cycle
• Common failure signs: no or weak agitation; no spin or slow spin
• Other symptoms include loud grinding/rumbling, oil leaking from the center area, or the motor running while the tub doesn't move

• Disconnect power and water; move the appliance to a stable work area and use proper lifting support
• Access the drive assembly from below; support the tub/frame to prevent tipping
• Mark component orientation, remove fasteners and drive components as needed, and transfer any reusable parts from the original unit
• Tighten mounting hardware evenly, then run a test cycle and check for leaks

This is a transmission assembly for washing machines. The transmission assembly is the gearbox in the washing machine's motor that allows the washing machine to work at different speeds and different intensities. If the washing machine is no longer spinning properly and has lost its normal level of washing power, it could mean that the transmission assembly needs to be replaced. Luckily, replacing this part is not as difficult as it might seem at first glance.To replace the transmission assembly, begin by unplugging the washing machine. The first step is to remove the upper control panel. Pull forward on the bottom of the console and remove the two retaining clips as well as the harness connector to the lid switch. Using a flathead screwdriver remove the clips. After this, remove the entire cabinet from the back panel to gain access to the interior of the washer. Remove the 7/16 bolt from the agitator and pull it straight up to remove it from the shaft. Once completed, gain access to the motor and pump and remove by releasing the screws and tabs that attach it. Remove the wire harness attached to the transmission. Remove the bolts that secure the motor mount to the transmission and proceed to pull the old transmission out of its place. Install the new transmission and reassemble the other parts.This genuine OEM replacement part is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse washers. It is sold individually.