Washer Dryer Combo Duct Parts

Side and bottom exhaust kit.

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This trap duct and felt kit restores the dryer's front airflow path and drum seal. Replacing a damaged duct or worn felt helps maintain proper airflow, improve drying performance, and reduce lint leaks and noise. What it does:

• Routes exhaust air through the lint filter housing to the blower
• Seals the drum front to prevent air leaks and reduce fabric snagging
• Helps address long dry times, lint escaping into the cabinet, and scraping/squealing from a worn front seal
• Replaces cracked, warped, or melted lint trap duct components

• One trap duct and one felt seal

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove top/front panels to access the lint filter housing and front bulkhead; support the drum as needed
• Clean mating surfaces; install the felt with the soft pile facing the drum to form a continuous, even seal
• Reuse original fasteners/hardware; the lint filter seats fully and the drum turns freely before testing

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

This duct exhaust directs and channels appliance exhaust air to the venting system to help remove heat, steam and odors from the unit. Fits into the appliance's vent path to restore proper airflow and venting performance. What it does:

• Channels exhaust air from the appliance to the household venting system
• Restores a sealed outlet path to reduce backflow and poor venting
• Helps prevent overheating and moisture buildup in the appliance cabinet area
• Commonly replaced when the existing duct is cracked, warped or missing

• Disconnect power and gas (if applicable) before servicing; follow manufacturer safety instructions
• Verify orientation and seating into the appliance vent before tightening fasteners
• Use proper venting materials and clamps when reconnecting to the home vent system

This exhaust vent extension provides extra duct length to move dryer or hood exhaust farther from the appliance, improving airflow routing and helping reduce backpressure and lint buildup in short-vent installations. What it does:

• Extends the length of an existing exhaust duct to reach a distant vent outlet
• Helps restore proper ventilation when original ducting is too short
• Reduces restricted airflow that can cause longer dry times or excess lint accumulation
• Works as an inline rigid/semirigid extension piece for exhaust systems

• Disconnect power (and gas for gas dryers) before accessing or modifying exhaust connections
• Remove lint and debris from ducting before installing the extension to ensure clear airflow
• Securely fasten with appropriate clamps or foil tape and maintain a smooth, unobstructed path

This exhaust vent extension restores proper exhaust airflow by lengthening or adapting the appliance exhaust outlet to the vent duct. It helps maintain safe ventilation and reduces backpressure that can cause poor performance or odors. What it does:

• Extends or adapts the appliance exhaust outlet to reach the home vent duct
• Directs exhaust airflow to reduce backflow and help prevent overheating
• Helps resolve symptoms like weak venting, lingering odors, or unusual appliance cycling
• Provides a stable connection point for the exhaust duct to improve sealing and airflow

• Turn off and disconnect power (and gas if applicable) to the appliance before installing.
• Use proper fasteners and high-temperature-rated duct tape or clamps as recommended by the appliance manufacturer.