Washer Dryer Combo Heating Element

The Dryer Heater Assembly is an OEM part for Frigidaire dryers. It is responsible for generating the heat necessary to dry clothes during the drying cycle. This assembly includes a back plate, ceramic insulators, a 5/16 inch terminal heater element already attached, and a dryer safety thermostat.

Over time, the heater assembly can fail due to factors such as regular wear and tear, overheating, or electrical issues. A faulty heater assembly can result in the dryer not producing enough heat or not heating at all, significantly affecting the appliance's performance.

Symptoms of a bad dryer heater assembly include:

• Dryer not heating or taking too long to dry clothes
• Clothes coming out damp after a full drying cycle
• The dryer shutting off prematurely or not reaching the desired temperature

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Electric Dryer Heating Element is an OEM replacement part for Frigidaire dryers. Located within the dryer drum cavity, this component produces the necessary hot air to evaporate moisture from wet laundry. Terminal Size: 5/16 inch. For the 1/4 inch terminal size order 5300622032. This electric dryer heating element restring coil does not include the heater housing insulators 131472100 or the terminal block 3202786.

Causes of element failure may be corrosion from atmospheric elements accumulating over time, cracks in filament coating from repetitive heating/cooling stresses, or exhaustion from workday after workday of extended use.

Symptoms of a bad electric dryer heating element include:

• Inability to achieve drying temperatures required for most fabric care
• Prolonged drying times reduce efficiency and convenience
• Absence of hot airflow from vents despite a running dryer

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replace a failed heating element with this Heater and Housing Assembly. It restores proper electric heat and airflow through the drum so loads dry evenly and within a normal cycle time. What it does:

• Generates heat as air moves through the element canister
• Replaces a broken, shorted, or open heater to restore drying performance
• Typical symptoms: no heat, very long dry times, drum tumbles but stays cool
• Often confirmed by an open (no continuity) reading on the element with a multimeter

• One heater and housing assembly

• Disconnect power by unplugging the dryer or switching off the circuit breaker; allow the unit to cool
• Access the heater housing, label wire positions, and remove mounting fasteners to swap the assembly
• Transfer any reusable brackets or hardware from the old unit as required by your model
• After installation, confirm good airflow and clean the vent/duct to prevent overheating and repeat failures

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This replacement heating element restores proper electric heat inside the dryer so clothes dry consistently and on time. A worn or open element can leave loads damp or extend cycle times; swapping it brings heat output back to spec.

• Generates the electric heat used during drying
• Common failure signs: no heat, long dry times, partial heating, or tripping the thermal cutoff
• Visual cues can include broken/warped coil or obvious burn spots
• Restores normal temperature rise for even drying performance

• Disconnect power before servicing; elements run on high voltage
• Access typically from the front or rear depending on model; note wire positions
• Avoid touching the coil with bare hands; handle by the frame
• Inspect thermostats/thermal cutoff if the old element failed

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

The Heater and Housing Assembly is an OEM part for GE electric dryers. As the main heat source, the heater coil works together with the housing to effectively heat air flowing through the dryer. Precisely maintaining optimal drying temperatures is crucial to the drying process. 

Symptoms of a bad heater and housing assembly include:

• Inefficient or prolonged drying times 
• Excessive lint accumulation inside the housing
• Rust or damage visible on the heater coil
• Odors produced from a burnt-out or shorted heater element

Causes can be normal wear over time, moisture damage if the housing is not cleaned regularly, or an internal short if the heater coil is cracked or broken.

This heater and housing replacement is also compatible with Hotpoint, RCA, and some Kenmore electric dryer models.

This bake heating element replaces the oven's primary heating element to restore consistent bake performance and even oven temperatures. Designed to heat quickly and quietly for reliable cooking results. What it does:

• Heats the oven cavity for baking and general cooking cycles
• Replaces a cracked, visibly burned, or non-heating element
• Helps restore oven temperature recovery and cooking consistency
• Stops symptoms like no heat, weak heat, or uneven browning

• Disconnect power at the breaker before servicing the oven
• Remove the oven racks and access the element from inside the oven
• Secure mounting screws and electrical connectors firmly; avoid overtightening