Washer Wire, Harness, Power Cord

This wire harness routes power and signals between the appliance control and internal components, restoring reliable electrical connections for normal operation. It replaces a damaged or frayed harness to help resolve intermittent power or control issues. What it does:

• Provides the bundled wires and connector plugs that link the main control to motors, switches, sensors, and heating elements
• Restores broken or corroded connections that can cause intermittent operation or failure to start
• Helps address symptoms such as controls not responding, burners/heater not powering, or intermittent motor/pump operation
• Matches OEM connector groupings to ensure correct plug fit and routing when replacing the original harness

• 1 wire harness as shown

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness
• Compare the replacement harness to the original to ensure connector types and wire routing before installing
• Secure harness routing away from heat sources and sharp edges; use existing clips or ties
• If you see burnt connectors or melted insulation, inspect surrounding components for underlying faults before restoring power

This door release cable connects the dryer door latch to the release mechanism so the door opens and closes reliably. Replaces a worn or broken cable to restore normal door operation and improve safety. What it does:

• Transfers motion from the door handle to the latch so the door can be opened and closed
• Helps ensure the door stays securely closed during operation
• Commonly replaced when the door won't latch or handle feels loose
• Prevents intermittent door-release failures that can stop dryer cycles

• Disconnect power before beginning any repair to avoid shock or injury
• Inspect the latch, handle, and routing path and replace any damaged clips or fasteners
• Basic hand tools typically required; follow OEM instructions for routing and attachment

This wiring harness connects the control panel to the oven's main control, delivering power and signal paths so the console and electronic controls operate correctly. It restores reliable button, display, and control communication when the harness is damaged. What it does:

• Routes power and signal lines between the control/console and main control board
• Replaces frayed, burned, or interrupted wires that cause unresponsive buttons or intermittent control behavior
• Helps restore normal display illumination and keypad response when the original harness is faulty
• Maintains proper connector fit and strain relief to prevent shorts or loose connections

• One wiring harness for the control panel

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Document or photograph wiring locations before removal to ensure correct reinstallation
• Handle connectors by the housings; avoid pulling on wires to prevent damage
• After installation, restore power and test all control functions before reassembling outer panels

This wire harness assembly routes power and signals between appliance components to restore proper electrical connections and reliable operation. It replaces a damaged or worn harness to help eliminate wiring-related failures. What it does:

• Provides the main electrical connections between controls, motors, switches, and sensors
• Transmits power and control signals so components respond correctly
• Replaces frayed, burned, or broken wiring that can cause intermittent function
• Helps address symptoms such as components not powering on, intermittent operation, or loss of specific functions

• Disconnect power (unplug or switch off breaker) before starting any work
• Note connector locations and routing before removing the old harness; reinstall in the original routing
• Inspect connectors and terminals for damage; replace harness if insulation or wires are compromised

This ATC wiring harness connects the appliance's ATC control to the wiring harness, restoring reliable electrical connections for temperature/controls. It's a direct-fit replacement that helps resolve intermittent power or control failures caused by damaged wiring. What it does

• Links the ATC control to the main wiring harness so signals and power reach the control
• Repairs broken or frayed wiring that can cause intermittent operation or loss of control
• Helps stop error codes or control failures related to poor connections
• Restores a secure, insulated connection to prevent shorting or arcing

• One ATC wiring harness

• Disconnect power to the appliance before servicing to avoid shock or damage
• Match connector shape and wire colors to the original before disconnecting any plugs
• Replace only with the correct harness to ensure proper fit and function

This genuine power cord assembly restores safe electrical connection to your appliance by replacing a damaged or worn power lead. Durable wiring and molded connectors help ensure a reliable feed for normal operation. What it does:

• Replaces a faulty or damaged power lead to restore power flow to the appliance
• Provides a secure, molded connection between the appliance and household power
• Can stop symptoms like no power, intermittent power loss, or tripped breakers caused by a compromised cord
• Helps eliminate loose or exposed wiring that can cause arcing or electrical smell

• Disconnect appliance from power before inspecting or replacing the cord.
• Match connector orientation and seating; secure strain relief and routing per appliance harness.
• Inspect mounting points and strain relief; do not use if connectors or wiring show damage.