Cap, Lid & Cover

A clutch cover assembly is bolted to the engine and has the clutch disc between it and the pressure plate. The springs within the clutch cover will force the pressure plate against the disc, moving it against the flywheel to send power into the manual transmission. This is a clutch cover assembly for Husqvarna and Craftsman chainsaws, including gear with the Poulan named attached. This is the cover for the assembly and ships as an individual part. It does not contain any of the other components associated with the transfer of power to the transmission.

This chainsaw fuel cap assembly is made from high-quality plastic. Durable threads keep this chainsaw fuel cap assembly working for years of use. You place one end in the fuel tank while the screw cap covers the nozzle. This keeps your gas from spilling out and causing possible damage or injury. You can’t cut down a tree or slice up some firewood with gas leaking everywhere. This also leads to harming the environment around you. Chainsaws fuel caps can swell. The rubber seals may leak after a certain amount of use. The cord attaching the cap to the insert may break, allowing the cap to be lost. Replacing the chainsaw fuel cap assembly can correct these problems. Pliers or a wrench may be needed to remove the old fuel cap assembly. This genuine OEM chainsaw fuel cap assembly was manufactured for use with Craftsman chainsaws. It is also compatible with Poulan and Poulan Pro chainsaws.

This steering boot is a genuine Husqvarna part, sold individually. This steering boot can be used as a replacement part in a lawn mower. The purpose of a steering boot in a lawn mower is to seal off the area outside of the rack and pinion so that debris cannot pass through into the machinery.The steering boot in a lawn mower might need to be replaced if the component can no longer serve its function. This could occur if the seal is broken as a result of general wear and tear from long-term use or from an accident that punctures, scrapes, erodes, or warps the part beyond basic functionality. If this occurs, the steering boot should be removed and replaced by this genuine OEM replacement part before using the lawn mower again. It is a simple repair process that will require only basic tools to conduct properly.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This steering boot is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, Murray, and Ariens.

This is a tank cap assembly that is used on many models of chainsaws. It is located on the fuel tank and is designed to ensure all fuel stays within the container. A retainer is included with the tank cap assembly to prevent dropping the cap and allowing dirt and debris into the fuel tank. An O-ring is used to seal the cap in the proper position. Tank caps can be damaged or lost, which can lead to dirty fuel, so the part will need to be replaced.Before replacing the tank cap assembly, make sure the chainsaw is off and the engine is cool. Place the chainsaw on its side and unthread the original tank cap assembly if it is still present. Pull the retainer from the fuel cap. Replacing the cap requires no special tools, but a pair of work gloves can be helpful. Take the new tank cap assembly and place the retainer into the tank. Thread the new cap on and tighten it before use.This part is made to be compatible with Poulan and Craftsman chainsaws. This tank cap assembly is an authentic OEM part that is priced as an individual part. It is directly obtained from the manufacturer.

This is a replacement engine guard that will work with a range of mowers. As the name suggests, the engine guard is used to help keep the engine of the mower safe. It will help to keep debris and other materials from getting into the engine. If the engine guard is broken or cracked, it could lead to problems with the engine from foreign debris. Replace this part as soon as possible.The engine guard is made from quality material and is designed to be durable. However, because it is on the front of the mower, it can suffer a substantial amount of wear and tear. There is also the possibility of damaging the guard while operating the machine. Owners should be able to replace the guard with no issue.The engine guard will work as a replacement for select models of zero-turn mowers from Husqvarna. The piece is sold individually. It is a genuine OEM replacement part that has been sourced directly from the manufacturer.

This chainsaw throttle wire cap acts as a protective covering for the throttle wire component. The throttle wire is a part that connects the chainsaw trigger with the carburetor so the engine can accelerate. When the chainsaw trigger is squeezed, the carburetor vent opens to allow fuel into the chamber. The more the part is squeezed, the faster the engine goes. The throttle wire cap can become damaged if the chainsaw is damaged through a drop or impact.To replace the throttle wire cap, close the choke lever and unscrew the cover on the air filter. Unscrew the nuts to remove the air filter and remove the throttle rod from the carburetor. Unscrew the screw on the bottom of the handle and lift it away from the trigger. Move the lever to run and lift the interlock lever. Pull the throttle wire out of the cap to remove it. The new part can be installed with the throttle wire.The throttle wire cap is made to be compatible with Husqvarna, Craftsman, Poulan, and Weed Eater chainsaws. It is priced on an individual basis. The part is an authentic OEM replacement component directly obtained from the manufacturer.

This replacement part is a steering lever and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. Steering levers are important in many different types of ridden lawn mowers and assist the user in ensuring the proper movements during use.A new steering lever might be needed if the current one is not working properly. This can be due to normal wear and tear over time. It is common that the steering lever can become stripped over time. If the user is having trouble steering smoothly or notices that the steering of the machine is rigid, it can be due to a worn-down steering shaft. Be sure to wear work gloves when replacing this part. It is also recommended that the engine be powered off. This is a genuine OEM replacement part to ensure proper fit and long-lasting use. This steering lever is sold individually and is sourced directly from the manufacturer.

This replacement part is a hubcap, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Hubcaps are placed on different tires to protect the frame of the wheel itself.A new hubcap might be needed if the current one is broken or damaged in anyway. It is possible for a hubcap to become damaged over time and can even fall off. If this is the case on any lawn mower, it is best to replace the hubcap. This repair should be fairly simple and require no more than common household tools. Be sure the engine is powered off so that the wheels are unable to spin during the repair. Be sure to purchase the correct amount of hubcaps as this part is sold individually. This is a genuine OEM product sourced directly from the manufacturer.

This shroud debris cover is a genuine MTD part, sold individually. This shroud debris cover can be used as a replacement part in a string trimmer. The purpose of the shroud debris cover in a string trimmer is to protect the appliance fromdebris within the internal mechanisms of the appliance, reducing the risk of damage to the infrastructure.The shroud debris cover might need to be replaced if the cover is damaged or compromised to the point that external materials can pass into the appliance and accumulate. The shroud debris cover could be dented, punctured, scraped, torn, scratched, eroded, warped, or otherwise damaged; if this occurs, the shroud debris cover should be removed and replaced by this genuine OEM replacement part, in accordance with the instructions sourced from a relevant appliance manual.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This shroud debris cover is compatible with the following outdoor appliance brands: MTD and Cub Cadet.

This replacement part is a blower housing. This is a genuine replacement part made by Midwest Engine. This part is responsible for the blowing mechanisms used in different types of leaf blowers or snow blowers. A new blower assembly might be needed if the current blowing mechanisms are not working as properly as in previous uses. If the air is not being expelled from the machine, it is most likely due to a faulty blowing assembly. If this is the case, it should be replaced as soon as possible. Refer to the user manual for more instructions on how to replace this part properly and safely. This blower assembly is a genuine OEM replacement part to ensure proper fit. This part is also sold individually and is sourced directly from the manufacturer.

A valve cover is a small but important piece of hardware designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as a snow blower or a tiller. It is compatible with products by brands such as MTD, Yard Machines, Troy-Bilt, Yard Man, Cub Cadet, Bolens, and Husky.The valve cover part is crucial because it plays a big role in keeping the engine protected and healthy. The valve cover is a type of casing that can be found on the top of the machine's engine. It covers the valves of the engine, which in turn protects the machinery from the elements and prevents oil leaks. Over time, natural wear and tear with exposure to the elements will occur, leaving evidence on the valve cover in the form of cracks, corrosion, and misalignment of the valve cover. If the valve cover shows signs of wear such as these listed, it can make fluid leak into the engine compartments. If this happens, it is very serious and will ultimately lead to engine failure.The replacement or repair process of the valve cover should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This valve cover is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.