Cooktop Gasket & Seal

The Seal is an OEM part for Frigidaire ranges. It creates an airtight seal between the oven and cooktop surfaces to contain heat and contain spills. Located around the edges of the oven cavity and cooktop surfaces, the pliable and flexible seal conforms precisely to fit the contours and gaps. 

Symptoms of a bad Range Seal include:

• Excess heat escaping from oven cavity around edges  
• Discolored or melted seal from continuous heat exposure
• Gaps allowing spills to leak underneath surfaces
• Increased energy costs from heat loss

This replacement is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

This door gasket seals the refrigerator/freezer door to keep cold air in and maintain consistent temperatures. A correct replacement restores the door seal to help prevent leaks, frost buildup, and inefficient cooling. What it does:

• Replaces a damaged or worn door seal to restore a tight closure between door and cabinet.
• Helps stop cold air from escaping, reducing frost buildup and uneven temperatures.
• Minimizes energy loss caused by gaps or cracks in the existing gasket.
• Addresses symptoms such as visible cracks, gaps when door is closed, or increased running time.

• One white door gasket (as pictured).

• Unplug the appliance or shut off power before starting any repair.
• Inspect and clean the gasket channel and mating surfaces before installing the new seal.
• Start by seating the gasket into the corners, then press the gasket evenly into the channel around the door.
• Avoid using sharp tools that could tear the gasket; refer to the appliance manual for any model-specific steps.

This small burner gasket seals the cooktop burner to help keep spills and debris out of the burner cavity for more reliable ignition and easier cleaning. It replaces a worn or brittle gasket to restore the burner's fit and seal. What it does:

• Creates a tight seal between the cooktop and the small surface burner to help prevent food, liquid, and debris from entering the burner area
• Helps maintain consistent burner alignment for reliable ignition and even heating
• Reduces the need for frequent deep cleaning by blocking spill penetration
• Commonly replaced when the gasket is cracked, flattened, burned, or missing

• One small burner gasket

• Disconnect power to the appliance before servicing; for gas ranges, turn off the gas supply when applicable
• Remove burner components and replace gasket, ensuring it seats evenly around the burner opening
• Do not force or stretch the gasket; inspect surrounding components for damage and clean surfaces before installing

This switch seal is a replacement gasket that helps keep moisture and debris away from the appliance's door/control switch, protecting the switch assembly and helping restore reliable door detection and operation. What it does:

• Seals the area around the door/control switch to block water, lint, and grime.
• Helps prevent intermittent trips or failures caused by moisture or foreign material contacting the switch.
• Promotes consistent switch actuation and can extend the service life of the switch assembly.
• Useful when the existing seal is cracked, torn, flattened, or missing.

• Disconnect power before servicing to avoid electrical shock.
• Access typically requires removing the door trim or control panel—follow your model's service instructions.
• Inspect the switch and surrounding area for damage or corrosion and clean before installing the new seal.

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This control seal sits in the control area of your range or cooktop. It creates a barrier that helps keep spills, grease, and debris out of the manifold/console for smoother control operation and longer component life.

• Seals the gap around control openings to block spill intrusion
• Helps protect internal valves/switches from moisture and debris
• Aids reliable knob/control function after cleanups and spills
• Common signs it's needed: cracked, deformed, or missing seal; liquids passing through control openings; gritty or sticky knob feel

• Disconnect power; also shut off gas. Allow the appliance to cool.
• Pull the control knob straight off and remove the old seal.
• Clean and dry the mating surface; seat the new seal evenly and flat.
• Reinstall the knob and verify the control turns freely with the seal fully seated.

This glass and shaft seal assembly replaces a damaged oven door glass seal and the shaft seal that helps keep heat and moisture contained. Restores proper sealing to improve oven performance and reduce heat loss. What it does:

• Seals the gap around the oven door glass and shaft to help contain heat and cooking vapors
• Reduces heat transfer and prevents excess moisture buildup near the door area
• Helps maintain consistent oven temperatures by restoring a proper seal
• Commonly replaced when you see visible wear, cracked/brittle seal, or heat leaking from the door edge

• One glass and shaft seal assembly as shown

• Disconnect power to the appliance before beginning any repair
• Handle glass components carefully to avoid breakage or injury; wear work gloves and eye protection
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This replacement knob grommet cushions and centers a control knob on the console, helping reduce wobble and protect the panel from wear for smoother, more secure knob operation. What it does

• Centers and cushions the control knob for proper alignment and tactile feel.
• Helps reduce knob wobble, rubbing, and wear on the control panel.
• Can address symptoms like loose, uneven-feeling, or noisy knobs when turning.
• Fits the knob mounting on compatible Whirlpool control panels for a restored fit.

• Disconnect power to the appliance before servicing.
• Remove the control knob, press the grommet into the panel opening, then reinstall the knob; generally requires no special tools.
• Inspect the knob and shaft—replace if damaged, as a damaged shaft can prevent a secure fit.
• Reconnect power and confirm proper knob alignment and operation after installation.

This is a replacement M5 x 20 gasket designed to restore a secure seal where the original small rubber gasket has failed. It prevents leaks and maintains proper pressure or fluid routing in the assembly. What it does:

• Provides a tight seal at the specified M5 x 20 connection to stop drips and seepage
• Restores proper seating for valves, fittings, or small housings that use this gasket
• Helps prevent airflow or fluid loss that can cause poor appliance performance
• Addresses common symptoms such as minor leaks, moisture buildup, or loose-fitting parts

• Replace with the appliance powered off and water/gas disconnected where applicable
• Inspect mating surfaces for damage or debris and clean before installing the new gasket
• Lubricate lightly with approved lubricant only if specified by the manufacturer

This side-trim gasket seals the edge of the appliance door/trim to help maintain a clean fit and reduce rattling or light air leakage. It restores the door edge seal for a neater appearance and improved closing performance. What it does:

• Seals the door side trim to help reduce noise and prevent light air or moisture intrusion
• Helps maintain proper alignment and fit of the door trim for smooth opening and closing
• Replaces worn, torn or compressed trim gasket that can cause rubbing or gaps
• Supports overall door aesthetics by restoring a continuous seal line

• One side-trim gasket

• Basic trim removal may be required
• Inspect mating surfaces and remove old adhesive or debris before installing the new gasket
• Use gentle pressure to seat the gasket; avoid stretching or over-tensioning
• Disconnect power to the appliance before doing any service that exposes electrical components

Seals the appliance door to prevent leaks and keep the interior working as intended. Replace a cracked, torn, or hardened gasket to stop leaks, reduce odor and mold, and restore a reliable door seal. What it does:

• Forms a tight seal between the door and cabinet to prevent water, air, or heat loss
• Stops common symptoms like visible cracks or gaps, water pooling, and persistent odors
• Restores proper containment for cleaning, heating, or washing cycles
• Matches the OEM channel/retainer design for a secure fit

• Disconnect power and water before beginning any repair
• Remove the old gasket, thoroughly clean the mounting area, then seat the new gasket into the door channel or retainer
• Work the gasket evenly around the door; avoid overstretching and ensure all beads/clips are fully engaged