Dishwasher Axle, Roller, Pulley Parts

Upper dishrack roller kit. 2 per package.

This drum roller supports the dryer drum so it spins smoothly and quietly. Replacing a worn roller restores stable drum rotation and helps reduce rubbing, scraping or thumping noises during operation. What it does:

• Supports and guides the dryer drum for even, stable rotation
• Reduces friction and drum wobble that can cause noisy operation
• Helps the drive belt track correctly and maintain proper drum alignment
• Common symptom: squeaking, thumping, or rubbing sounds and uneven spinning

• Disconnect power before starting any repair
• Remove the dryer drum or access panel to inspect and replace the roller; support the drum while removing/reinstalling
• Check other drum rollers, bearings and the drive belt for wear and replace as needed to prevent repeat failure
• Reassemble carefully and test with the dryer empty to ensure smooth, quiet rotation

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement

This wheel and bearing assembly mounts to the upper dishrack, allowing it to glide smoothly in and out on the rail. Replacing a worn or broken wheel restores smooth operation and helps keep the rack securely on track.

• Supports and guides the upper rack along the side rails
• Restores smooth rolling and proper rack alignment
• Helps prevent the rack from binding or derailing
• Common symptoms: rack hard to slide, falls off track, wheel cracked/missing, squeaking or grinding as the rack moves

• Disconnect power before servicing; remove the upper rack from the rails by releasing the rack stops
• Release the old wheel/bearing from the rack tabs and remove
• Snap the new assembly into the rack mounting holes until it locks
• Reinstall the rack and verify smooth travel on both rails

This dishwasher tub wheel mounts to the inner side of the tub and supports the rack track as it moves. Replacing a worn wheel restores smooth glide and helps keep the rack aligned during loading and unloading.

• Supports the rack track on the tub wall
• Keeps the rack moving smoothly and aligned
• Reduces friction and noise during operation
• Failure signs: rack hard to slide, squeaking or grinding, rack tilting or coming off track, cracked/missing wheel

• Disconnect power and water supply before servicing
• Pull out the rack and remove track end caps or the rack, as needed, to access the wheel
• Remove the retaining screw/clip, install the new wheel, and verify it spins freely and seats fully
• Reassemble and test rack movement through full travel

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This dishrack roller and stud assembly lets the rack glide smoothly in and out of the dishwasher. Replacing a worn or broken wheel restores proper rack movement and helps prevent binding, noise, and derailment. What it does:

• Attaches to the rack wire with an integrated stud/clip to provide a rolling wheel on the rack rail
• Restores smooth, even rack travel and alignment
• Replaces cracked, missing, or seized rack wheels
• Common symptoms: rack is hard to slide, wobbles or comes off track, or the wheel is visibly damaged

• One roller-and-stud assembly

• Disconnect power before servicing; work with dry hands
• Pull the rack fully out and lift it off the rails
• Release the old stud from the rack wire, position the new assembly, and snap/lock it in place with the wheel oriented to the rail
• Reinstall the rack and verify smooth movement

This roller kit replaces worn or broken drawer rollers so a refrigerator or freezer drawer opens and closes smoothly. It restores proper drawer alignment and reduces sticking or dragging for easier access to stored food. What it does:

• Replaces damaged or worn rollers that cause drawers to stick, bind, or sit unevenly
• Guides the drawer along its track for smooth, consistent movement
• Reduces noise from grinding or scraping during drawer operation
• Helps maintain proper drawer alignment to prevent jams and protect the glide track

• One roller kit assembly

• Disconnect power to the appliance before beginning any repair to avoid injury
• Remove the drawer and inspect the slide/track for damage or debris before installing the new roller
• Installation typically requires basic hand tools and removing the drawer from its track; follow the OEM diagram for correct placement
• If the track or other components are damaged, replace them as recommended by the OEM

Color: White. For gray order WD35X21041. Roller only. Does not include axle. For axle order WD35X21041. Updated by the manufacturer. May be wider than original.