Dryer Axle, Roller, Pulley Parts

I ordered a new motor. Read more

Changed the drum rollers, belt, and idler pulley wheel. Was not sure which one was making the noise but all three were well used and many years old. One of the drum wheels was the culprit. very easy and straightforward repair with no assistance. Read more

Replace idler wheel assembly, belt and spring. Read more

• Will not tumble

Replaced the tension pulley assembly, drum rollers, drum roller axles, belt, and drum glides while I had the dryer disassembled. It turned out that the cause of the squeak was the tension pulley assembly, however it was easy and economical enough to replace anything that could have been the cause of the squeaking while I had the dryer apart. The parts were ordered on Thursday afternoon and delivered on Friday. I had the dryer repaired and running like new in no time. For about $100, it was... Read more

I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more

Took dryer apart. Replaced roller, 45 minutes, done. Read more

• Noisy

Order set of drum rollers. My dryer required four. As long as I was opening up the dryer, dryer, 10 years old, I wanted to replace all of them. Also ordered new belt for Sam reason. Found full manual online. Disassembled dryer, about 20 screws. Replaced rollers, although only one was squeaky. Put it all back together. Took about 3 hours. Read more

I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside. Read more

Un plugged dryer. It was an easy fix, popped the top up. Removed the two screw that held the front on and also unclipped the door switch. Released tension that was on belt and removed drum. Removed old front slides cleaned up area and replaced them. Popped the ring that held the rear drum wheels and placed the new ones with a dab of grease. Un hooked tension spring for idler and removed old one and put the new one in. Make sure you place it through the correct hole and it makes it firmly into... Read more

After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more

Decided to order the kit with both rollers even thou the right one looked OK.Also ordered the pulley for the idler. Watched the video for the pulley installation,super helpful on a couple of the steps!! Everything went great. A 14 year old dryer still has life! Parts ordering and delivery was also great!!! Thank you. Read more

I took the tumbler drum out and looked at the pulley and it was not rotating freely. The idler arm had some wear on the attached post so I replaced bothe parts. Since I was in there already I replaced the drum rollers and dryer belt for good measure. I reassembled the dryer and it works great. The best part of the experience was the parts order. I ordered the parts around 3:00 pm one day, standard shipping, and they were on my doorstep around 1:00 pm the next day. I'm still wondering... Read more

Replaced front drum roller wheels and rear drum bearing.Pull plug. Remove 2 screws holding top panel,slide rearward and lift panel off. Remove all screws from back panel,wiring cover and cord clamp. Remove back panel and feed cord through hole.No need to remove cord. Remove 2 screws from heater box and let it drop rearward.Remove belt from motor pulley and let tensioner rest against motor pulley.This step will trigger the switch that disables motor if belt breaks.The switch does not reset... Read more

• Noisy

Had to replace the drum rollers, idler roller and belt. Machine has never been taken apart so it was a learning event as well as cleaning all the internals components. Parts that were purchased fit fine, no problem with figment. More time was spent oncleaning and prepping the machine for the new parts Read more