Electrolux Bumper, Bushing, Grommet Parts

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install

This rubber bumper cushions doors and panels to reduce noise, prevent metal-on-metal contact, and protect finishes for smoother, quieter operation. Replace worn or missing bumpers to help restore proper seating and reduce rattling. What it does:

• Absorbs shock between moving parts to prevent bangs and scratches
• Keeps doors and panels aligned for a tighter seal and quieter close
• Reduces vibration and rattling during operation
• Helps protect painted or plated surfaces from wear at contact points

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Typically a push-in or snap-in replacement; press into the original mounting hole until seated
• Inspect nearby bumpers and replace in matched sets if others are cracked or missing

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance

This spacer positions and supports components to maintain proper alignment and clearance in the appliance. It prevents rubbing and ensures panels or parts sit correctly for reliable operation. What it does:

• Keeps panels, brackets or assemblies spaced correctly to prevent contact and wear
• Restores proper alignment to reduce vibration, noise or rubbing symptoms
• Maintains clearance for airflow or moving parts where specified
• Provides a stable mounting point for adjacent components

• One spacer

• Install in the location shown in the service diagram and secure with the original fasteners
• Disconnect power to the appliance before beginning service to avoid shock or injury
• If the original spacer shows damage or distortion, replace it to restore correct fit

This rubber grommet cushions and secures wiring, tubes, or panels to prevent chafing and reduce vibration. It helps keep components aligned and quiet for reliable appliance operation. What it does:

• Cushions parts where metal meets metal to prevent wear and chafing
• Dampens vibration and reduces rattling or squeaking noises
• Holds wiring or tubing in place to maintain proper routing
• Helps protect against abrasion and occasional minor movement

• Disconnect power and leave appliance unplugged before starting any repair
• Remove the damaged grommet and clean surrounding area before installing the new piece
• Press or stretch the grommet into place; use gentle tools (plastic trim tool) to avoid damage
• Inspect adjacent wiring/tubing for damage and replace if frayed or pinched

This replacement cam is the small rotating actuator that engages and controls movement in compatible appliance mechanisms, restoring proper engagement and smooth operation where the original cam has worn or broken. What it does:

• Transfers rotational motion to a latch or linkage to enable proper opening, closing, or dispensing actions
• Ensures consistent engagement and timing of the associated mechanism
• Common symptoms it can fix: intermittent or failed latching, loose or sloppy movement, clicking or grinding noises during operation
• Small, precision part used where alignment and rotation are required

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle small parts carefully and keep track of fasteners and orientation for correct reassembly
• Installation may require removal of exterior panels or a control assembly; refer to the service manual or diagram for step-by-step guidance

This snap bushing is a push-in panel grommet that protects and secures wiring where harnesses pass through metal or plastic panels. It prevents chafing and helps keep wire routing neat for safer operation. What it does:

• Cushions and shields wires from sharp panel edges to reduce abrasion and shorts
• Secures wiring harnesses in place to prevent unwanted movement or snagging
• Provides a finished, vibration-resistant pass-through for electrical leads
• Commonly replaced when the original bushing is cracked, broken, or missing

• One snap bushing

• Disconnect power before servicing electrical components
• Press-fit into the panel hole until the bushing snaps into place; confirm a secure fit
• Replace if brittle, torn, or deformed; do not use a damaged bushing
• Use pliers for removal if needed; avoid forcing or enlarging the hole