Electrolux Insulation, Sound Dampening Parts

This insulation panel fits inside the refrigerator cabinet to help maintain interior temperatures and reduce heat transfer to the outer shell, supporting more consistent cooling and helping limit frost buildup. What it does:

• Forms a thermal barrier between the interior liner and outer cabinet to help hold cold air inside.
• Helps reduce frost and moisture buildup around the liner when intact.
• Worn, torn, or missing insulation can contribute to longer run times, uneven cooling, or more frequent defrost cycles.
• Replaces damaged insulation to restore proper temperature retention and improve appliance efficiency.

• Always disconnect power to the appliance before starting any repair.
• Panel may be secured with clips, adhesive, or foam sealant; remove and install carefully to avoid damaging the liner.
• Inspect surrounding seals, gaskets, and fasteners while accessing the cavity; replace any damaged components.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This vibration dampener cushions and isolates vibrating components to reduce noise and movement, helping your appliance run more quietly and smoothly. It's a simple replacement that restores proper mounting and stability. What it does:

• Absorbs vibration from compressors or motors to cut down on rattling and buzzing
• Keeps mounted components aligned and prevents metal-to-metal contact
• Helps reduce transfer of vibration into the cabinet and surrounding surfaces
• Commonly replaced when excessive noise, shaking, or loose mounts are present

• One vibration dampener

• Disconnect power to the appliance before servicing
• Support the component (compressor/motor) before removing mounts to avoid shifting
• Typically press-fit or bolted into place; use basic hand tools as required
• Replace any damaged fasteners and secure mounting before restoring power

This dampener regulates airflow inside the refrigerator to help steady temperatures between compartments and reduce temperature swings. It replaces a worn or broken air control piece to restore proper circulation and consistent cooling. What it does:

• Controls airflow between fridge compartments to help maintain even temperatures
• Helps reduce warm or cold spots caused by stuck or broken dampeners
• Minimizes rapid temperature changes when doors open and close
• Operates quietly as part of the internal air distribution system

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; handle plastic parts carefully to avoid breakage
• Verify correct orientation and secure mounting for proper airflow operation

Air duct insulation that fits over the refrigerator air duct to reduce condensation and help direct airflow for more consistent cooling. Replaces worn or torn duct insulation to help prevent moisture buildup and improve efficiency. What it does:

• Wraps around the refrigerator air duct to insulate and reduce condensation
• Helps maintain consistent air temperature as it moves between compartments
• Reduces moisture and frost buildup on the duct and surrounding components
• Restores original fit where torn, compressed, or missing insulation causes issues

• Before starting, disconnect power to the appliance to avoid electrical hazards
• Remove access panels per your model's service instructions to reach the duct
• Slide or wrap the insulation around the duct, ensuring full coverage and a snug fit
• Replace any damaged fasteners or adhesive strips; test operation and check for proper airflow after reassembly

This insulation piece fits inside the refrigerator cabinet to help maintain internal temperatures and reduce heat transfer, improving cooling stability and efficiency. It replaces worn or damaged insulation behind liners and panels. What it does:

• Provides thermal barrier between cabinet and exterior to help the cooling system maintain set temperatures
• Reduces cold-spot development and helps prevent excessive frost buildup behind liners
• Dampens vibration and minor noise from compressor and refrigerant movement
• Supports proper airflow pathways by filling gaps around panels and components

• One insulation piece as shown

• Disconnect power before beginning any work; for sealed-system safety, unplug the appliance
• Access typically requires removing interior liners or access panels—keep fasteners and clips organized
• Handle insulation gently to avoid tearing; replace any damaged retaining clips or adhesives

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer

This evaporator block is the refrigerator evaporator coil assembly that removes heat from the freezer/refrigerator compartment to help maintain proper cooling and reduce frost buildup. What it does:

• Circulates refrigerant through the evaporator to absorb heat from the compartment
• Promotes cold airflow across the freezer and fresh-food sections when paired with the evaporator fan
• Helps control frost and ice buildup on the evaporator surface
• Common symptoms: reduced cooling, excessive frost or ice buildup, or warm freezer temperatures

• Always disconnect power to the appliance before servicing
• Replacing the evaporator typically requires accessing sealed refrigerant areas;
• Allow components to fully defrost and drain before removal to avoid water damage
• Handle the coil gently to avoid bending fins or damaging tubing