Electrolux Parts

The Thermostat is an OEM replacement part for Frigidaire dryers. It plays a crucial role in monitoring and regulating the temperature inside the tumbler. The thermostat works closely with the heating element and controls to accurately sense temperature fluctuations and modulate heating levels accordingly.

Symptoms of a bad thermostat include:

• Clothes taking an overly long time to dry
• The dryer is heating excessively and tripping the breaker
• Temperature display or heater lights not functioning
• Clothes drying unevenly, still damp in spots

Causes can be normal wear over extreme heating and cooling cycles. Environmental contaminants may also impact sensor performance.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Ice Chute Door Insulation is an OEM replacement part for Frigidaire refrigerators. It is installed on the ice chute door to prevent warm air infiltration and moisture buildup around the ice dispenser.

Causes may include compression or cracking of insulating foam/material from normal use stress. Spills exposing it to liquid are also damaging.

Symptoms of defective insulation consist of:

• Ice accumulating within the chute cover area
• Condensation visible on exterior chute surfaces
• Inefficient icemaker performance due to altered temperatures

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Defrost Heater is an OEM replacement part for Frigidaire refrigerators. It is an electric heating element located within the back wall and along the evaporator coil compartment. The heater defrost works to melt any accumulated frost or ice during refrigeration defrost cycles. 

Causes of a bad defrost heater include failure of the heating coil or wiring over time due to regular use. Moisture exposure can also degrade insulation and connections.

Symptoms of a bad defrost heater include: 

• Ice buildup inside the refrigerator that does not melt   
• Inability to maintain proper cooling temperatures
• Frost accumulating externally on refrigerator coils
• Unusual smells emanating from within the appliance 

This OEM Frigidaire replacement defrost heater restores automatic defrost capabilities. Compatible with some Electrolux, Roper, and Kenmore models as well, regular replacements prevent defrost issues.

This broil heating element mounts at the top of the oven cavity to provide intense, direct heat for broiling and to assist with preheating. Replacing a failed element restores even broiling performance and helps the oven reach temperature properly.

• Provides high, top-down heat for broiling
• Common failure symptoms: no broil heat, uneven browning, trips breaker when broil is selected, visible hot spots or breaks in the element
• Helps with overall oven preheat and temperature recovery

• Disconnect power before service; the element is high-voltage
• Remove oven racks to access mounting screws
• Support wiring when transferring leads to the new element to prevent panel damage
• Avoid touching new element with bare hands; clean any oils from terminals

This washer tub-to-pump hose connects the outer tub to the drain pump, carrying wash water out during the drain cycle. Replacing a cracked, clogged, or leaking hose helps stop leaks, restore dependable draining, and prevent water damage.

• Directs water from the outer tub to the drain pump during drain and spin
• Common symptoms: water leaking under the washer, water left in the drum, slow or no drain, or drain-related error codes
• Wear, heat, or debris/foreign objects can cause splits, soft spots, or blockages
• Restores a sealed flow path to improve drainage and reduce leaks

• Unplug the washer and turn off water supply; use gloves and have towels or a shallow pan ready for residual water
• Access the pump area through the lower front or rear service panel (varies by model)
• Note routing/orientation; move clamps back, seat the new hose fully on both fittings, and resecure clamps
• Run a short rinse/drain cycle and inspect all connections for leaks

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

The Timer Knob Assembly is an OEM replacement part for Frigidaire electric dryers. This assembly incorporates the timer dial, stem, and mounting components that allow users to set desired drying periods.

Causes of a faulty timer knob include wear and tear of internal gears from regular cycle selections. Damage to the outer dial or stem connection points may also occur.

Symptoms include: 

• Inability to rotate timer dial through full drying options   
• Timer selections not initiating or maintaining set programs
• Dial detaching from the front panel during adjustment

This OEM Frigidaire replacement part is compatible with Electrolux, Gibson, and various Kenmore dryer models as well.

The Clock is an OEM part for Frigidaire ranges. This part includes the display and control board that manages the oven's timer, clock functions, and sometimes additional settings such as cooking timers and delayed start features. 

Causes of a bad clock can include electrical issues, wear and tear from regular use, or physical damage from impacts or spills.

Symptoms of a bad clock include:

• The clock display not functioning or showing incorrect time
• Inability to set or use the timer functions
• The oven not responding to control inputs
• Error codes or intermittent operation of the control panel

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

The Grease Filter is an OEM replacement part for Frigidaire microwaves. It traps grease-laden smoke and particles released from cooking. Color: silver. Measures about 6 inches wide by 8 inches deep.

Causes of a bad grease filter can include clogging from accumulated grease and debris, physical damage from cleaning or handling, or wear and tear over time. A clogged or damaged filter can reduce the efficiency of the range hood, leading to poor ventilation and potential damage to the range hood motor.

Symptoms of a bad grease filter include:

• Reduced airflow or suction
• Excessive smoke or odors during cooking
• Grease buildup on kitchen surfaces
• Visible damage or clogging of the filter

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Damper is an OEM replacement part for Frigidaire refrigerators. It controls the flow of cold air circulating inside the fridge compartment including the damper seals. The damper opens and closes automatically depending on temperature conditions to maintain proper cooling levels.

Causes of a bad damper can include seal failure allowing air leaks over time, restricted movement from mineral deposits binding internal parts, or physical damage bending critical damper components.

Symptoms of a bad damper include:

• Inability to achieve recommended temperature settings
• Areas inside the fridge feeling warmer than others
• Fluctuating temperatures requiring frequent adjustments

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drain Hose is an OEM part for Frigidaire washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle.

You should replace the drain hose if it becomes damaged or clogged. Causes of a bad drain hose include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Container is an OEM replacement part for Frigidaire refrigerators. It is responsible for storing ice produced by the ice maker.

Causes of a bad ice container can include wear and cracks that develop over repeated use and cleaning. Minerals or scale deposits may also accumulate inside over time.

Symptoms of a bad ice container include:

• Ice spilling or leaking out of the container 
• Cracks or breaks that compromise the storage cavity
• Chipping of the plastic coating inside the container

This OEM Frigidaire replacement part is compatible with refrigerators from Electrolux, Gibson, and Kelvinator as well.

The Water Inlet Valve is an OEM component for Frigidaire washing machines. It resides within the base and precisely controls water intake into the washer tub. 

Symptoms of a bad water inlet valve include:

• Failure to fill the tub with water for cycles  
• Residual water leaks at the valve area
• Inability to select fill levels on newer machines
• Restricted or no water flow into hoses

Causes may be mineral sediment buildup inhibiting valve function over time, worn internals allowing leaks, or electronic issues in smart valves.

Compatible with units including Electrolux, Gibson, and select Kenmore models as well. Renewed laundry performance awaits with this vital component repair.
 

The Condenser Fan Motor is an OEM replacement part for Frigidaire refrigerators. It is a component responsible for drawing heat away from the refrigerator's cooling system. By rapidly spinning the condenser fan blades, the motor works to dissipate heat buildup and ensure optimal cooling performance.

Causes of a bad condenser fan motor include bearing wear over time, damage from moisture or dirt infiltration, or failure of electronic motor components. 

Symptoms of a bad condenser fan motor include:

• Inadequate or inconsistent cooling within the refrigerator 
• Loud buzzing or rattling noises emanating from the rear
• Slow or failed rotation of the condenser fan blades

This OEM Frigidaire replacement condenser fan motor is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore-branded refrigerators. 

The Burner Orifice is an OEM replacement part for Frigidaire gas ranges and cooktops. It controls the mixture of gas and air delivered to each burner element.  

Symptoms of a faulty orifice can include:

• Inconsistent or unpredictable burner flame heights 
• Yellow flames that create excess soot or carbon buildup
• Potential risk of flashback into gas lines

Causes may involve gradual damage from normal usage, such as cracks developing. Improper cleaning can deposit residue that changes flame characteristics as well.

This OEM Frigidaire replacement restores balanced gas flow regulation. Compatible with ranges from Electrolux, Gibson, and select Kenmore models.