Need Help?
Call
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replaced clamp with a new one Read more
Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.
After examining it, 2 of the 4 retainer clips had broken off. My wife grabbed her tablet, found Appliance Parts Pros website, saw 2 videos featuring our exact model of washer and ordered the 3 parts to replace broken and soon to fail parts ! Shipping was extremely fast ! Took out old assembly, replaced with new assembly in about 15-30 second, wife was happy, therefore I was happy ! Thx for being there ! Read more
Washer won't spin or makes loud whining noise? The drive motor powers drum rotation. Moderately difficult repair, takes 30-60 minutes. Video guide available.
I watched videos on the website and took it apart. Put new motor on, also I put new belt even though the original belt was still ok, but I saw a little sign of shredding ...and there! !! It works like brand new washing machine. . Thanks to appliancepartspros.com...It made save a lot of money by doing it myself.. Read more
Freezer won't stay cold or runs too cold? A faulty heat exchanger disrupts refrigerant flow. Requires professional brazing and refrigerant recharge.
Had a friend who is an appliance repair tech. Replace the evaporator, the heater coil, and the filter/drier. Parts were soldered together and the compressor was put under vacuum. Then, charged with 5 oz. of refrigerant. The freezer works great now! Read more
Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.
Installed the new bracket as per instructions with template enclosed and it was perfect. Read more
Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.
Burner cap sits atop the gas burner base to distribute flame evenly. Replace if cracked, warped, discolored, or missing to restore proper heat distribution.
Found web site. Called the 800 number. Placed the order. 2 days later, they were at my door. Read more
The Water Filter Bypass is an OEM replacement part for Frigidaire refrigerators. It provides an alternative water supply route to bypass the refrigerator's built-in water filtration system. The bypass allows refrigerator water and ice dispensers to operate without water flowing through the installed filter cartridge.
Causes of a malfunctioning bypass can include mineral buildup inhibiting proper operation of the bypass valve, worn seals or O-rings not providing a tight seal or physical damage.
Symptoms include:
This OEM replacement is also compatible with refrigerator brands like Electrolux, Gibson, Kelvinator, and select Kenmore models.
Just used a bypass filter with great results with water flow and taste Read more
Collects water from evaporator defrost cycles. Mounts near compressor under refrigerator. Replace if cracked, leaking, or damaged to prevent odors.
Previously, I removed the lower rear cardboard back of the unit and saw the crack in the defrost pan. It was probably damaged when unit was moved using appliance hand truck. I looked up the part number AP4319611 in the exploded view diagrams of the unit. The part was ordered and delivered in a few short days. Emptied the unit and removed all shelves/glass to avoid damage since the unit must be tilted enough to reach under and remove two 1/4 inch hex screws. Tilted to the right side (facing... Read more
Secures the crisper slide rail to the refrigerator liner for smooth drawer operation. Replace if broken or missing to restore proper alignment and support.
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair. Read more
Replace your cracked, broken, or worn range oven door handle. Restores secure grip and fresh appearance for smooth opening and closing of doors or drawers.
I ordered the replacement handle and replaced it myself. Read more
Oven won't heat or can't hold temperature? This thermal switch monitors oven temperature and protects internal components. Common fix for heat issues.
After 2 repair men, many parts replace it still didn't work, Did research on line and found out the thermal fuse would need to be replace.. Read more
Spacer that provides clearance between the range oven door handle and door surface. Replace if cracked, broken, or missing to ensure proper handle fit.
I orderd parts you said I needed, but all I needed was a handle. I will keep other parts for future needs Read more
Replacement surface burner head for gas ranges and cooktops. Distributes gas through precision ports for even flame. Needed when original is clogged, damaged, or corroded.
Conversion kit said put propane orifice .109 in to correct the problem but I had to use the .102 orifice. Read more
This is a top burner gas valve that controls the flow of gas to a surface burner on a gas range. It connects to the burner control knob and regulates the flame from low to high settings. Replace this valve if a surface burner won't ignite, the flame is difficult to adjust, or you detect a gas smell even when the knob is in the off position.
Replacement surface burner valve. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.