Electrolux Parts

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This replacement glass panel restores a smooth, sturdy surface to your refrigerator or freezer shelf/cover assembly, helping contain spills and safely support stored items so your food stays organized and accessible. What it does:

• Replaces cracked, missing, or stained shelf/cover glass to restore a flat storage surface
• Helps contain spills to prevent drips onto lower shelves or drawers
• Supports food items evenly to reduce tipping or wobbling
• Improves overall shelf stability and cleanliness

• 1 glass panel

• Unplug the appliance and wear cut-resistant gloves when handling glass
• Remove the shelf/cover assembly; note orientation before disassembly
• Carefully slide out the old glass, clean the frame/rails, and seat the new glass fully
• Ensure the panel is evenly supported on all sides before reloading items

This position-specific ice crusher blade (#1) fits inside the refrigerator's ice bucket assembly. It helps break up cubes into crushed ice; replacing a bent or worn blade restores consistent crushing and reduces jams or grinding noises during dispensing.

• Works with the auger and other numbered blades to crush ice when "Crush" is selected
• A bent, dull, or corroded blade can lead to no crushed ice, only cubes, slow dispensing, or scraping/grinding noises
• Restores even crushing and smoother auger rotation
• Position- and orientation-specific within the blade stack; match to your original

• Disconnect power and switch the ice maker OFF before servicing
• Remove and empty the ice bucket; allow any frost to thaw
• Disassemble the bucket front/auger and note the exact blade order and orientation—take photos for reference
• Wear cut-resistant gloves; reassemble blades, spacers, and washers exactly as removed and verify the auger turns freely before reinstalling

The Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for controlling the temperature and operation of the warming drawer or zone feature.

Causes of a bad Switch can include electrical malfunctions or short circuits, mechanical wear from repeated use, and exposure to moisture or debris.

Symptoms of a bad Switch include:

• Inability to activate or control the warming drawer or zone
• Erratic temperature fluctuations
• Overheating or failure to heat the warming area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Fan Motor Assembly is an OEM part for Frigidaire wall ovens. This part powers the fan responsible for circulating air within the oven, ensuring even heat distribution for consistent cooking and baking results.

Causes of a bad fan motor assembly can include wear and tear over time, electrical issues such as short circuits or power surges, and physical damage from debris or impacts. 

Symptoms of a bad Fan Motor Assembly include:

• The oven not heating evenly or taking longer to reach the desired temperature
• Unusual noises coming from the oven during operation
• The fan not running or running intermittently
• Error codes related to the fan or airflow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Wash Arm Bearing is an OEM replacement part for Frigidaire dishwashers. It is a crucial component that supports and facilitates the smooth rotation of the wash arm during the dishwashing cycle. The wash arm is responsible for spraying water and distributing detergent solution evenly throughout the dishwasher tub, ensuring thorough cleaning of dishes.

Causes of a bad wash arm bearing include wear and tear over time, exposure to debris or hard water buildup, or physical damage due to impact or mishandling. A faulty bearing can lead to issues with the wash arm's rotation and water distribution.

Symptoms of a bad wash arm bearing include:

• Excessive noise or grinding sounds during the wash cycle
• The wash arm not rotating or spinning properly
• Uneven or incomplete cleaning of dishes
• Water not being distributed evenly within the dishwasher tub

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.

Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.

Symptoms of a bad drive motor include:

• The washing machine not spinning or agitating
• Loud, unusual noises during operation
• The washer not starting or stopping mid-cycle
• Burning smell or visible signs of motor overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

The Spacer is an OEM part for Frigidaire ranges and ovens. This part provides the necessary clearance between the oven door handle and the door itself, preventing friction and wear while ensuring the handle is securely attached and easy to use. This small but crucial component aids in the proper functioning of the oven door, making it easier and safer to open and close without exerting extra force.

Causes of a bad Spacer include mechanical stress leading to cracks or breaks, improper installation that may result in loosening over time, and degradation from heat exposure and frequent use.

Symptoms of a failing Spacer include:

• Loose oven door handle.
• Difficulty in opening or closing the oven door.
• Visible gaps or misalignment of the door handle.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement door bin mounts on the inside of your refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or loose bin restores safe, usable storage and helps keep items organized and accessible.

• Provides storage on the door to keep bottles and jars upright
• Restores capacity when the original bin is cracked, warped, or missing
• Helps prevent items from tipping or falling when the door opens/closes
• Common symptoms: bin falls off, won't stay seated, or has broken tabs/cracks

What's included: 1 door bin Install notes:

• Remove all items from the old bin; lift straight up to release from the door slots
• Align the new bin's tabs with the slots and press down until fully seated
• Do not force; re-align if resistance is felt to avoid damaging the door liner
• Place in the correct door position for your model; some bins aren't interchangeable between levels

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

The Spring is an OEM part for Frigidaire washing machines. It is a component that assists the movement of the inner basket or tub during the wash cycle. The spring plays a crucial role in dampening vibrations and absorbing shocks to provide stability, preventing excessive noise and movement.

Causes of a spring failure can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the spring, or damage due to impact or mishandling.

Symptoms of a bad Spring include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or walking during operation
• Leaks due to increased stress on the tub and other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This is the factory handle set for select Frigidaire-built appliances. It restores a secure, comfortable grip and fresh appearance so doors or drawers open and close as intended. What it does

• Provides the handhold needed to open and close the appliance door or drawer
• Replaces cracked, broken, or missing handles
• Helps correct loose or wobbly handles that won't stay tight
• Refreshes worn or scuffed handles for a cleaner look

• Manufacturer-supplied handle set

• Disconnect power before servicing; allow hot surfaces to cool
• Remove interior/hidden mounting screws and the old handle
• Align and secure the new handle; re-use existing hardware/brackets if applicable
• Do not overtighten fasteners; verify smooth door/drawer operation

This glass turntable tray provides a stable, heat-resistant surface that rotates food inside the microwave for more even cooking and reheating. It replaces a damaged or missing tray to restore proper rotation and support. What it does:

• Supports plates, bowls and containers while the microwave's turntable motor rotates them for even heating.
• Transfers rotation from the drive coupling through the roller/guide assembly to the glass tray.
• Restores stable, level rotation when the original tray is cracked, chipped, or missing.
• Helps prevent food spills inside the cavity by providing a flat, easy-to-clean surface.

• One glass turntable tray.

• Handle the glass carefully to avoid chips or cracks; wear gloves if necessary.
• Place tray onto the roller/guide and align with the drive coupling; it turns freely before use.
• Clean with mild detergent and non-abrasive cloth; do not use if the glass is cracked or severely chipped.
• If rotation problems persist after replacing the tray, check the roller/guide and drive coupling for wear.

The Gasket is an OEM part for Frigidaire washing machines. This part is located between the front and rear outer tubs and prevents water leaks by maintaining a watertight seal between them. The gasket acts as a barrier to ensure that water used during the washing process remains contained within the inner tub, preventing it from seeping into the washing machine's surrounding components.  

Causes of a bad gasket can include regular wear and tear, exposure to harsh detergents, or deterioration over time.  

Symptoms of a bad gasket include:

• Water leaking from the outer tub area
• Visible cracks or deterioration in the gasket material
• The washing machine not holding water properly
• Increased noise or vibration during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.