Frigidaire Bumper, Bushing, Grommet Parts

This oven light button is the user-facing push button used to operate the oven light. It restores a damaged or missing control button so the light can be turned on and off easily. What it does:

• Acts as the push button for the oven light control assembly.
• Replaces cracked, worn, or missing oven light buttons that are hard to press or no longer stay in place.
• Helps restore normal user control of the oven interior light without replacing the entire switch assembly.
• Fits into the existing control panel opening and interfaces with the factory light switch mechanism.

• Turn off power to the appliance before attempting any repair to avoid shock—unplug or switch off the breaker.
• Remove control panel trim or bezel as required to access the button; retain all fasteners for reassembly.
• Inspect the underlying switch and wiring; replace the switch if the button does not resolve the issue.

This switch bushing fits the control shaft to stabilize and guide rotary switches, helping restore proper knob alignment and smooth operation. It prevents wobble and uneven contact that can cause intermittent control behavior. What it does:

• Centers and supports the control shaft to keep the switch and knob aligned
• Reduces wobble and lateral play that can make knobs feel loose or inconsistent
• Helps maintain reliable electrical contact by keeping the switch properly seated
• Commonly replaced when knobs are loose, the switch wobbles, or control engagement is uneven

• One switch bushing

• Disconnect power to the appliance before starting any repair
• Requires removing the control panel or knob to access the switch shaft; small hand tools typically needed
• Inspect the switch and knob for wear while replacing the bushing; replace worn components as needed

This spacer positions and supports components to maintain proper alignment and clearance in the appliance. It prevents rubbing and ensures panels or parts sit correctly for reliable operation. What it does:

• Keeps panels, brackets or assemblies spaced correctly to prevent contact and wear
• Restores proper alignment to reduce vibration, noise or rubbing symptoms
• Maintains clearance for airflow or moving parts where specified
• Provides a stable mounting point for adjacent components

• One spacer

• Install in the location shown in the service diagram and secure with the original fasteners
• Disconnect power to the appliance before beginning service to avoid shock or injury
• If the original spacer shows damage or distortion, replace it to restore correct fit

This rubber grommet cushions and secures wiring, tubes, or panels to prevent chafing and reduce vibration. It helps keep components aligned and quiet for reliable appliance operation. What it does:

• Cushions parts where metal meets metal to prevent wear and chafing
• Dampens vibration and reduces rattling or squeaking noises
• Holds wiring or tubing in place to maintain proper routing
• Helps protect against abrasion and occasional minor movement

• Disconnect power and leave appliance unplugged before starting any repair
• Remove the damaged grommet and clean surrounding area before installing the new piece
• Press or stretch the grommet into place; use gentle tools (plastic trim tool) to avoid damage
• Inspect adjacent wiring/tubing for damage and replace if frayed or pinched

This snap bushing is a push-in panel grommet that protects and secures wiring where harnesses pass through metal or plastic panels. It prevents chafing and helps keep wire routing neat for safer operation. What it does:

• Cushions and shields wires from sharp panel edges to reduce abrasion and shorts
• Secures wiring harnesses in place to prevent unwanted movement or snagging
• Provides a finished, vibration-resistant pass-through for electrical leads
• Commonly replaced when the original bushing is cracked, broken, or missing

• One snap bushing

• Disconnect power before servicing electrical components
• Press-fit into the panel hole until the bushing snaps into place; confirm a secure fit
• Replace if brittle, torn, or deformed; do not use a damaged bushing
• Use pliers for removal if needed; avoid forcing or enlarging the hole

A small sleeve used to support and align a shaft, pin, or lever inside the appliance. Replacing a worn bushing restores smooth, quiet movement and helps prevent accelerated wear on adjoining parts for reliable operation. What it does:

• Supports and centers a rotating or sliding shaft/pin
• Reduces friction and metal-to-metal wear to minimize noise
• Helps maintain proper alignment for consistent performance
• Common signs of wear: wobbling play, squeaks/grinding, binding, or visible cracks

• One bushing

• Disconnect power and shut off gas/water before servicing
• Note the original orientation; seat the new bushing fully and squarely
• Clean mating surfaces; inspect shafts/pins for wear and replace if damaged
• Apply manufacturer-approved lubricant only if specified by your service manual

This sealing plug caps an access hole or opening to prevent leaks, debris entry, or airflow in the appliance. It restores a finished seal and helps keep internal components protected from moisture and dirt. What it does:

• Covers and seals an unused service or access opening to prevent water and dirt intrusion
• Keeps loose parts and debris from falling into internal compartments
• Helps maintain proper airflow routing and prevents rattling from an open hole
• Commonly needed if the original plug is cracked, missing, or brittle

• Disconnect power and water before servicing the appliance
• Verify correct plug orientation and push fully into the opening until seated
• Replace any damaged retaining clips or surrounding gaskets to ensure a proper seal
• If the hole is deformed or the plug does not seat securely, stop and confirm correct part before continuing