Frigidaire Gasket & Seal

The Freezer Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the freezer door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper freezing conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the freezer
• Difficulty keeping the freezer door fully closed
• Warm air entering the freezer, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This adhesive seal tape is a replacement sealing strip used to restore a tight seal on appliance doors and panels, helping reduce air leaks and improve temperature control. It's a simple repair for worn or damaged seal edges. What it does:

• Provides a flexible, adhesive sealing surface to close gaps between door/panel and cabinet
• Helps reduce air or moisture leakage that can cause temperature loss or inefficient operation
• Restores worn or deteriorated sealing surfaces without replacing the entire gasket
• Compatible with applications where a narrow adhesive sealing strip is required

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the tape to fit; press firmly along the full length to ensure contact
• Allow adhesive to set per ambient conditions before closing the door or returning to service

This drum glide is a front drum support that stabilizes the dryer drum and helps it turn smoothly, reducing rubbing noises and uneven wear. Replacing a worn glide restores quiet operation and proper drum tracking. What it does:

• Provides a low-friction surface for the drum front to ride on and prevents metal-to-metal contact
• Reduces squeaks, scraping, or rubbing noises caused by a worn support
• Helps keep the drum aligned so clothes tumble evenly and the belt runs correctly
• Protects the drum and bulkhead from scoring and premature wear

• One drum glide

• Disconnect power (and shut off gas supply for gas dryers) before starting any repair
• Remove the dryer front panel or bulkhead per your model's service instructions to access the glide
• Inspect other drum supports, rollers, and the belt while the dryer is open; replace any worn components
• Use basic hand tools; follow OEM procedures and torque recommendations where specified

This replacement door gasket fits the refrigerator compartment. It forms a tight seal between the door and cabinet to help keep cold air in, limit moisture at the door, and maintain consistent temperatures. What it does:

• Seals the fresh food door opening to prevent air leaks
• Helps maintain stable interior temperature and humidity
• Reduces condensation and frost around the door perimeter
• Common failure signs: torn, warped, or compressed gasket; door not sealing; persistent condensation; temperature fluctuations; longer run times

• 1 refrigerator fresh food door gasket

• Disconnect power before servicing
• Lay the gasket flat to relax; gently warm with hot water or low heat to remove kinks
• Remove the old gasket; on many models, lift the liner lip or loosen retainer screws to release it
• Press the new gasket fully into the channel; check corners for a uniform seal and adjust door alignment if needed

This replacement sealing gasket restores a tight, reliable seal between mating parts in your appliance. A proper seal helps prevent leaks and bypass, reduces noise, and supports overall performance and efficiency.

• Creates a compressible seal between components to prevent air or moisture bypass
• Helps maintain correct airflow/temperature containment for proper operation
• Reduces vibration and rattling caused by hardened or damaged seals
• Replace if the original is torn, flattened, brittle, missing, or leaking

• Disconnect power before servicing; shut off water supply if applicable
• Remove the old gasket and clean mating surfaces of residue/debris
• Match the original routing/orientation; do not stretch or over-compress the gasket
• Tighten fasteners evenly to ensure a uniform seal; verify no pinching or gaps

This door gasket seals the perimeter of the refrigerator or freezer door to maintain an airtight closure. Replacing a worn gasket restores a proper seal, helps stabilize temperatures, reduces frost and condensation, and supports efficient operation. What it does:

• Creates a tight seal between the door and cabinet to keep cold air in and warm air out
• Helps reduce frost buildup and moisture around the door opening
• Can address temperature fluctuations, long run times, and doors that won't fully close
• Replace if torn, deformed, brittle, or no longer sealing evenly

• 1 door gasket

• Disconnect power before servicing; open the door and remove the old gasket from its retainer/channel
• Warm the new gasket (soak in warm water) to relax and straighten before installation
• Seat the corners first, then work evenly around the perimeter to fully engage the retainer
• Close the door and check for uniform contact; adjust the gasket/retainer as needed for a complete seal

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

Replacement refrigerator door gasket restores a proper seal around the refrigerator door to help maintain steady internal temperatures and reduce frost, condensation, and cold-air leakage. Helps keep food fresher and supports consistent cooling. What it does:

• Seals the door-to-cabinet gap to help prevent cold air from escaping and warm air from entering.
• Helps reduce frost buildup and interior condensation when the door seals correctly.
• Common replacement when the gasket is torn, deformed, flattened, or the door no longer seals tightly.
• Restores sealing contact along the full door perimeter to support temperature stability.

• Disconnect power to the appliance before attempting any repair.
• Clean and dry the door flange and gasket channel before installing to ensure a proper seal.
• Seat gasket evenly around the door; inspect for gaps and correct fit before returning appliance to service.
• Follow OEM instructions for any recommended conditioning (warming/softening) or final adjustments.

This freezer door gasket forms the airtight seal between the freezer door and cabinet. Replacing a worn or damaged seal helps keep cold air in, reduce frost buildup, and restore proper temperatures and efficiency.

• Creates a tight perimeter seal to prevent warm air leaks and moisture intrusion
• Helps maintain stable freezer temperature and humidity
• Reduces frost and ice accumulation around the door area
• Common symptoms: visible gaps or tears, door not sealing fully, condensation at the door edge, heavy frost near the door

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use gentle, low heat) to relax and ease installation; do not overheat
• Remove the old gasket; seat the new gasket fully into the door channel (some models require loosening and retightening retainer screws)
• Verify an even seal all around; perform a paper/dollar-bill test and adjust corners as needed

This door gasket creates an airtight seal around the refrigerator door to help maintain proper cooling and energy efficiency. Replaces a worn, torn or hard-to-close seal to reduce moisture and keep food fresher. What it does:

• Seals the door perimeter to help maintain consistent internal temperatures
• Prevents warm, humid air from entering and forming frost or condensation
• Helps the compressor run less frequently by improving cabinet efficiency
• Reduces drafts, cold spots and premature spoilage caused by a damaged seal

• Clean the door channel and remove old gasket before fitting the new seal
• Warm the gasket with a hair dryer (low setting) if needed to make installation easier

This is a replacement refrigerator door gasket that restores the seal around the door to help maintain proper temperature and efficiency. It's a direct-fit sealing strip designed to replace a worn, torn, or deformed door seal. What it does:

• Seals the gap between the door and cabinet to help keep cold air in and warm air out
• Helps reduce frost buildup and prevents moisture and leaks around the door
• Restores consistent internal temperature for better food preservation
• Reduces compressor run time caused by an improper door seal

• One refrigerator door gasket

• Recommended: replace gasket on a clean, dry door surface; remove old gasket and adhesive residue before installing
• Use the manufacturer's recommended attachment method (snap-in or adhesive) for your model
• Inspect hinge alignment and door fit before finalizing gasket installation to ensure an even seal
• For safety, unplug the appliance or disconnect power before beginning repairs

This burner seal fits the 17k burner to restore a snug seal between the burner and cooktop, helping keep spills out of the burner assembly and keeping the flame properly aligned. Ideal for restoring a cleaner, more reliable cooktop surface. What it does:

• Creates a tight seal around the 17k burner to help prevent food and liquid from entering the burner cavity
• Keeps burner head seated correctly so the flame pattern stays consistent
• Helps reduce soot and residue buildup around the burner area
• Useful when the original seal is cracked, compressed, or missing

• One burner seal for a 17k burner (single piece)

• Always shut off power and gas supply before servicing the range
• Remove burner head and clean mating surfaces before installing the new seal
• Fit the seal in the correct orientation so the burner seats evenly; reassemble parts in reverse order
• After installation, restore power/gas and verify proper burner operation; follow manufacturer's instructions for leak checks and testing