Frigidaire Handle

The Microwave Door Handle is an OEM part for Frigidaire microwaves. It provides a secure and convenient grip for opening and closing the microwave door. This handle is designed to fit seamlessly with the door’s structure, ensuring proper operation while maintaining the appliance's overall aesthetic.

Over time, microwave door handles can become damaged due to frequent use, accidental impact, or exposure to heat and moisture. Cracks, chips, or loosening of the handle can compromise its function and appearance, making it difficult to open or close the microwave door properly.

Symptoms of a bad Microwave Door Handle include:  

• A loose or wobbly handle  
• Cracks or visible damage to the handle  
• Difficulty in opening or closing the microwave door  
• The handle detaching completely  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement door handle restores a secure, comfortable grip for opening and closing your appliance door. Replace a cracked or loose handle to keep everyday use safe and convenient when the original is damaged or missing.

• Provides the handhold used to open and close the door
• Replaces cracked, broken, or missing handles to restore normal operation
• Addresses a wobbly/loose handle or stripped mounting points
• Common symptoms: handle broken, loose, or difficult to grip; trouble opening the door

• Disconnect power before servicing
• Support the door while removing and installing the handle
• Use the correct screwdriver; transfer any screw caps/end covers as needed and reuse original fasteners if applicable
• Tighten mounting screws evenly; do not overtighten, and ensure the handle is secure and aligned

The Handle is an OEM replacement part for Frigidaire ranges. It is the component located on the front of the oven that allows for opening and closing the oven door.

Causes of a bad handle stem primarily from wear and tear due to frequent use over many years. Exposure to heat cycling may also degrade adhesives or secondary components that secure the handle.

Symptoms of a faulty handle include:

• Difficulty opening or closing the oven door
• The handle detaching from the door
• Sharp edges or broken pieces that compromise safety
• Loss of grip or stability while moving the door

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Door Handle Set is an OEM part for Frigidaire refrigerators, ensuring a perfect fit and finish for your appliance. This set includes handles for both the refrigerator and freezer doors, designed to replace broken or worn-out handles, providing a secure and comfortable grip for opening and closing the doors.

Causes of damage to the door handle set typically involve physical stress, such as excessive force when opening or closing the door, accidental impacts, and general wear and tear over time. 

Symptoms of a bad Door Handle Set include:

• Handles that are loose or detached, making it difficult to open the door
• Cracked, broken, or worn handles that can lead to injury or further damage to the door
• Difficulty in aligning the handles during installation, indicating potential warping or damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door handle provides the grip to open and close the appliance door. Replace a cracked, loose, or missing handle to restore easy access and a clean, finished look.

• Provides the user handhold to operate the door
• Mounts to the door panel and transfers pull force to the latch mechanism
• Common symptoms: handle cracked/broken, loose or falling off, difficulty opening the door
• Helps address cosmetic damage or sharp edges from a broken handle

• Disconnect power to the appliance before servicing
• Open the door and support the outer panel or glass, if applicable
• Transfer and reuse original fasteners; align the new handle and tighten evenly—do not overtighten
• Verify smooth door operation before returning to service

Color: Black. For white order 5304440324. For bisque order 5304440325. For stainless order 5304461371.

The Handle Set is an OEM part for Frigidaire refrigerators. It includes the necessary handles for the refrigerator and freezer doors, providing a secure and ergonomic grip for opening and closing the doors. 

Causes of a bad handle set can include regular wear and tear, accidental impacts, or damage from overloading the doors.  

Symptoms of a bad handle set include:

• Loose or wobbly handles
• Visible cracks or breaks
• Difficulty in opening or closing the doors
• Handles not aligning properly with the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle Kit is an OEM replacement part for Frigidaire ovens and ranges. These handles provide safe access to the oven interior.

Causes of a bad handle kit can include normal wear over time of moving parts, accidental damage from impact or mishandling of the oven door, or issues with the latching mechanism.

Symptoms of a bad oven door handle kit include:

• Loose, sluggish, or difficult operation of handles
• Handles detaching from oven door
• Inability to fully open or close the oven door
• Problems with door sealing or staying closed securely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This handle trim replaces a damaged or missing trim piece on the appliance's door handle. It restores a clean, finished look by covering mounting hardware and helps keep the handle properly aligned for everyday use.

• Finishes the end of the door handle and hides visible screws
• Helps stabilize the handle and maintain proper alignment
• Restores appearance when the original trim is cracked, loose, or missing
• Common signs: broken or missing cap, exposed screws, wobbly handle

• Disconnect power before servicing
• Open the door to access the handle; remove the old trim by releasing its clips or fasteners
• Align and snap the new trim into place; transfer any hardware if required
• Do not overtighten fasteners to avoid damaging plastic parts

This replacement latch secures the door closed so the appliance can operate correctly. Restores a positive close and consistent door recognition to help prevent no-starts and intermittent operation. What it does / common symptoms:

• Engages the strike to hold the door/panel closed
• Ensures the door-closed signal is made so controls can run
• Worn or broken latch may cause the door not to stay shut
• Unit may not start, show a "door" message, or stop if the door is bumped

• 1 latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch per model—typically behind the front panel or inner door liner
• Note and transfer any springs/clips from the original latch to the new one
• Verify smooth open/close and proper strike engagement before testing operation

This handle insert fits into the handle assembly to cover mounting hardware and complete the finished look. Replace a missing or cracked insert to restore appearance and help protect the hardware underneath.

• Press-fits into the handle to conceal fasteners and provide a clean, finished appearance
• Helps keep debris out of the handle cavity and around screw heads
• Typical symptoms: insert broken or missing, exposed fasteners, rough or sharp handle opening edges

• Disconnect power before servicing; wear gloves to protect hands from sharp edges
• Carefully pry out the old insert with a plastic tool to avoid marring surrounding surfaces
• Align the new insert with any tabs/slots and press evenly until fully seated
• Tighten screws beneath the insert before installing the new piece

A white replacement handle assembly that restores a clean, functional door grip and appearance. Installs in place of a cracked, broken, loose or worn handle to make opening and closing smooth and secure. What it does:

• Replaces damaged or worn door handle for reliable grip and operation
• Restores original appearance on white finishes
• Stops cracking, splitting or loose-handle symptoms that affect use
• Matches OEM mounting points for a secure fit when installed correctly

• Disconnect power or unplug the appliance before servicing if your repair requires access near electrical components
• Use basic hand tools; follow OEM diagram for fastener locations and alignment
• Tighten fasteners securely but avoid overtightening to prevent cracking

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

The Spacer is an OEM part for Frigidaire ranges and ovens. This part provides the necessary clearance between the oven door handle and the door itself, preventing friction and wear while ensuring the handle is securely attached and easy to use. This small but crucial component aids in the proper functioning of the oven door, making it easier and safer to open and close without exerting extra force.

Causes of a bad Spacer include mechanical stress leading to cracks or breaks, improper installation that may result in loosening over time, and degradation from heat exposure and frequent use.

Symptoms of a failing Spacer include:

• Loose oven door handle.
• Difficulty in opening or closing the oven door.
• Visible gaps or misalignment of the door handle.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

This is the factory handle set for select Frigidaire-built appliances. It restores a secure, comfortable grip and fresh appearance so doors or drawers open and close as intended. What it does

• Provides the handhold needed to open and close the appliance door or drawer
• Replaces cracked, broken, or missing handles
• Helps correct loose or wobbly handles that won't stay tight
• Refreshes worn or scuffed handles for a cleaner look

• Manufacturer-supplied handle set

• Disconnect power before servicing; allow hot surfaces to cool
• Remove interior/hidden mounting screws and the old handle
• Align and secure the new handle; re-use existing hardware/brackets if applicable
• Do not overtighten fasteners; verify smooth door/drawer operation