By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
The Flipper Mullion Assembly is an OEM part for Frigidaire refrigerators. It is an exterior part that seals the refrigerator door and houses the water and ice dispenser on select models. The flipper mullion assembly attaches both side by side doors together and operates the dispenser and door functions. Causes of a bad mullion assembly can include damage from door impacts, wear from years of door swing motions, or failure of seals or gaskets. Symptoms of a bad Flipper Mullion Assembly include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Started with replacing hinges. Had to glue the door hinge to refrigerator and secured with two small screws. This refrigerator is in a business with about 50 employees. Suspect minion was not working for some time causing the hinges to get broken. . Read more
Secure door gaskets and interior trim on freezers and refrigerators. Replace broken or missing clips to maintain proper seal and temperature. Confirm fit.
Ordered a new seal, and replaced it with a new one freezer works great now. Read more
Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.
My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more
Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.
Ordered parts and now works perfectly. Read more
Top burner won't cycle temperatures or respond? This range burner control switch restores reliable heat regulation. Direct-fit replacement for electric and gas ranges.
Changed the control switch Read more
Replaces worn or broken refrigerator door hinge bearing. Installs between door and hinge bracket to support smooth opening and closing motion.
I went to Appliance Parts Pros and watched a few videos. Ordered the door closer plate and door hinge bearing. Removed all of the door bins and contents. Removed four screws total. Lifted the door off of the hinge, replace the two parts on the bottom hinge. Put the door back on the hinge with a little silicone on the new parts. Replaced all of the screws and no more popping. It took more time to clean all of the door bins than to fix the hinge. The video was 100% accurate. No surprises. Read more
Connects water filter to refrigerator system for clean water and ice. Replace if leaking, water flow is slow, or filter won't seal properly.
First we tried to change the filter. Water was leaking from the area of the filter when we changed the filter. We purchased an "original" Fridgidaire filter, no change. Did some research on the internet and decided to change the two tubes and the filter valve (at the back of the filter housing). Must have been the right diagnostic and the right part to make the repair, Gave me an opportunity to clean the condenser coils as well. After 6 years of service they needed it badly. Read more
Compressor clicks and won't run? This start relay kit fixes refrigerators that won't cool. Common fix for clicking compressor that shuts off. Easy install.
Thanking APP ahead of time for expedient 1 day express parts & videos! I kept a LOG on this repair fix starting 6/21/20: started with cleaning out behind the Frigidaire /coils, fan blade, floor, walls, toe-plate, compressor. #1 Replaced just the Run Capacitor [from my local appl store]. Somewhat better but not a fix. Fridge controls need much higher settings than Factory Settings - which is recommended. Did some homework on several sites /kept coming back to yours / saw what parts are probably... Read more
Fix frost buildup on evaporator coils causing warm temps or freezer icing. This defrost heater melts accumulated ice. DIY repair in 30-40 minutes.
REPLACED DEFROSTER, CONDENSER FAN MOTOR AND DEFROST THERMOSTAT. Read more
Refrigerator not cooling properly? A broken condenser fan blade prevents heat removal from coils. Easy DIY fix—just pull off and press on. Video included.
No local refrigeration house had one. APP did! I got it in 2 days. Everything is A OK. Read more
This is a shelf frame or carriage that supports the deli drawer cover inside the refrigerator compartment. It provides structural support for the glass or plastic shelf panel that sits above the deli or crisper drawer area. Replace this part if the frame is cracked, warped, or broken, causing the shelf to sit unevenly or fall out of position.
After removing the glass shelf the broken piece slid out easily and the new one then slid back in. Read more
This complete ice maker assembly automatically produces and harvests ice cubes for your refrigerator's ice storage bin. It fills with water, freezes it into cubes, and cycles them out when the harvest cycle activates. Replace this assembly if your ice maker stops working entirely, produces poor quality ice, or leaks water into the freezer.
My frig is a year and a half old, Frigidaire with french doors and freezer drawer. It has an upper ice maker for the door in the frig and a bottom ice maker in the freezer drawer. After noticing the flood, I shut off the water supply to the frig and cleaned up the mess. Didn't know if it was the water solenoid valve that stuck open or if the bottom ice maker got stuck calling for water. This frig has 4 solenoid valves and according to the schematic, two valves are active any time water is... Read more
The Solenoid and Yoke Assembly is an OEM part for Frigidaire refrigerators. It is used in the ice dispensing system to control the movement of the ice chute, allowing ice to be dispensed from the refrigerator door.
Causes of a bad solenoid and yoke assembly can include electrical issues such as a burnt-out solenoid, wear and tear from regular use, or physical damage due to mishandling or impact.
Symptoms of a bad solenoid and yoke assembly include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Replaced solonoid. Video was very helpful. Parts came in the time frame given when I ordered the part. (1.7 days). Without the video I would have called a repairman. Thanks . Read more
Dispenser only producing cubed ice? A cracked or broken crusher housing prevents crushed ice delivery. Moderate DIY repair in 30-60 minutes.
Replaced the housing Read more
Fix a cracked ice bin or broken auger in your refrigerator. This ice container assembly includes the storage bucket and auger. Moderate DIY repair.
Replaced the ice container assembly. Read more
Replacement cam riser for refrigerator door hinges. Installs at the top hinge assembly. Replace if cracked, broken, or worn to restore smooth door operation.
Replaced the lower hinge bearing and lower door cam on fridge side. Read more
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.