Frigidaire Support Parts

The Shelf Support is an OEM part for Frigidaire countertop microwaves. It holds and stabilizes shelving inside the microwave cavity during operation. 

Symptoms of a faulty shelf support include:

• Loose or detached shelves that cannot maintain placement  
• Difficulty positioning shelves at desired height levels
• Scrapes or dents on interior microwave walls from shelf movement
• Gaps or spaces where shelf legs do not sit securely  

Causes relate to typical wear of spring clips or brackets holding shelves in place. Regular vibration from microwave turntables can weaken pressure points over time.

This OEM replacement shelf is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Note: Quantity of two brackets

Support for broil heating element.

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

Front plate restores the appliance's front-facing cabinet, protecting internal components and improving appearance. It replaces cracked, dented or worn front trim so the appliance looks finished and covers internal parts. What it does:

• Covers and protects internal components behind the appliance's front cabinet.
• Restores cosmetic appearance when the existing front is dented, cracked, or scratched.
• Helps maintain proper fit and alignment of adjacent trim and access points.
• Reduces exposure of internal components to dust and incidental contact.

• Always disconnect power (and water, if applicable) before beginning work.
• Removal typically requires removing fasteners, clips or adjacent trim panels—keep track of all screws.
• Handle carefully; edges may be sharp and panels can be awkward to position alone.

The Trunnion is an OEM part for Frigidaire washing machines. It allows the outer wash tub to rotate during agitation and the spin cycles. The trunnion is a heavy-duty, durable component designed to withstand the rigors of repeated cycles and turbulent wash motions.

Causes of a bad trunnion can be wear over extended use, damage from unbalanced loads that strain the pivot point, or fractures from impact or manual mishandling.

Symptoms of a bad trunnion include:

• Excessive vibration or shaking during operation
• Noisy or grinding sounds emanating from the tub area
• Difficulty starting or stopping tub motions
• The tub failing to rotate properly during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This baffle plate secures internal panels and helps position or shield components for proper airflow and operation. It replaces a worn or damaged bracket to restore stable mounting and reduce vibration or rattling. What it does:

• Secures internal panels or assemblies to prevent movement and noise
• Helps direct or protect airflow paths around internal components
• Reduces rattling, vibration, and intermittent contact caused by loose parts
• Commonly replaced when a panel is cracked, bent, or no longer holds fasteners

• Disconnect power to the appliance before beginning any repairs
• Inspect surrounding fasteners and mounting points; replace any stripped or damaged screws
• Reuse existing hardware only if in good condition; use manufacturer-recommended fasteners when available

This support is a molded mounting bracket designed to secure and stabilize appliance components, helping keep parts properly aligned and preventing sagging or movement during use. Durable plastic construction for reliable long-term positioning. What it does:

• Secures panels, assemblies, or internal components to the cabinet or frame
• Keeps parts aligned to prevent binding, rubbing, or uneven wear
• Supports weight to reduce stress on fasteners and adjacent parts
• Helps restore original fit and function after breakage or loss

• One support mounting bracket

• Disconnect power and, if applicable, water before beginning any repair
• Confirm correct orientation and seating before fastening; use factory screw locations
• Use appropriate, non-stripping fasteners and do not overtighten
• If the original part is damaged, remove all debris before installing new support

This element mounting spring secures a surface cooktop heating element to the range, keeping the element stable and ensuring consistent electrical contact for reliable heating. Replaces a worn or missing spring to restore proper element fit. What it does

• Holds the surface heating element in place under the cooktop or in the drip pan.
• Maintains stable mechanical and electrical contact so the element heats evenly.
• Prevents element wobble, movement, or poor seating that can cause intermittent heating.
• Commonly needed when an element drops, rattles, or fails to make solid contact.

• Disconnect power to the appliance before starting any repair.
• Remove the element and/or drip pan per the range service instructions to access the spring.
• Install the spring in the same orientation as the original; ensure the element seats fully and securely.