Need Help?
Call
Fix a dryer that won't start, stops mid-cycle, or won't shut off with a new timer. Controls drying cycles and timing. 15-30 minute DIY repair.
Ordered both parts and got them in 2 days, removed 3 screws on back panel of dryer and removed defective timer , installed wires on new timer and put back in place and installed new knob , very easy repair only took 10 minutes and dryer was back up and running Read more
The washer start stop switch button is the physical push button on your washing machine's control panel that signals the machine to begin or pause a cycle. It connects to the underlying switch mechanism that sends an electrical signal to the control system. Replace this part when pressing the button does nothing, the button feels mushy or broken, or the washer will not start or stop responding to that control.
All I had to do was remove 3, 1/4" screws from the back and take the front off. Two 5/16th screws hold the circuit board in place, remove them and press the button into the hole from the back. Replace the circuit board, slide the front back on and install the three 1/4" screws. Always unplug the washer first! Read more
Converting your dryer from natural gas to propane? This LP conversion kit includes orifices and instructions. DIY-friendly in under an hour.
I searched the internet and found the conversion kit to LP gas at Appliancepartspros.com. their price was the least expensive. The instructions were excellent in describing the removal of the nat. gas orifice and replacement with LP orifice. The part was delivered 3 days after ordered by Fed Ex., a speedy delivery! I finished installing my clothes dryer and it works fine. I have some experience with such equipment but recommend professional installation for reasons of safety! Thank you, R.P. Read more
The Blower Wheel is an OEM replacement part for GE dryers. It has a role in the air circulation within the dryer, aiding in the even and efficient drying of clothes. The blower wheel, connected to the motor, helps in expelling the moist air out of the dryer through the exhaust vent during the drying cycle. Causes of a malfunctioning blower wheel are typically wear and tear from regular use, the accumulation of lint or debris, or damage to the wheel’s fins or central hub, which can impact its rotation and air circulation capability. Symptoms of a bad Blower Wheel include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
New wheel didn't look different than the other wheel, but we put it on, it works and we're very happy. Read more
This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
Supports and stabilizes the dryer drum for smooth rotation. Replace if you hear squealing, grinding, or the drum moves excessively. Confirm fit with your model.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
Replacement control knob for washing machines. Installs on the control panel to select cycle and temperature settings. Needed when cracked or broken.
Replaced the timer Read more
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying. Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions. Symptoms of a bad flame sensor include:
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes. Also, the old solenoids tested... Read more
Supports and stabilizes the dryer drum during rotation. Replace when you hear squeaking noise or notice excessive drum wobble. Verify fit with your model.
After taking off the top and front panels to access the drum, it was easy to see what the problem was. The front drum support was worn through and the 3 drum support glides were gone. The rear drum bearing was also completely worn out. And while I had the dryer apart I also replaced the idler pulley and drive belt. The only hard part was putting the drive belt back on the motor shaft and idler pulley. The dryer is back to drying clothes like a new machine. Read more
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also. Read more
Dryer drive belt connects the drum to the motor for tumbling action. Replace if your drum won't turn or you hear squealing. Confirm fit with your model.
The Dryer is 10 years old GE Front Load DPVH890JEMG. The drum would intermittently not rotate at the beginning of a cycle and occasionally would rotate but then start and stop throughout the cycle. I did not check error codes, but the windings on the motor were black. So it seemed reasonable that the motor was overheating and sending a signal to the control board to stop. There is one screw under the knob and 9 screws on the front to get inside. I decided to replace the bearings, capacitor,... Read more
Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.
Replaced cycling thermostat. Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
Replace your dryer's push to start button if cracked, broken, or worn. This button installs on the control panel. Commonly needs replacement due to wear.
Replaced the knob and it works perfect now Read more
The Thermistor is an OEM replacement part for GE dryers. This temperature-sensing device monitors air exhaust temperatures and communicates real-time readings to the control board. Precise thermistor functioning ensures the heating elements and drum engage safely and appropriately.
Symptoms of a faulty thermistor include:
Causes often relate to moisture exposure from normal operation degrading electronic performance over time. Physical stress or impact could potentially damage thin connecting wires.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryers.
Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.