Need Help?
Call
Replaces the cracked or warped crisper drawer frame that supports the glass shelf above vegetable drawers and forms the rails for smooth drawer sliding.
The new replacement parts were absolutely perfect! Plus, the new drawer had a molded-in reinforcement in the same spot the old drawer broke - design improvement that should keep the new drawer safe much longer. Replacement was a snap - just slide out the old, slide in the new. The real advantage was, while we were at it, we cleaned out all the old bottles, produce, leftovers, etc, so that the refrigerator is now as clean inside as the day we bought it. Also important to note that the parts were... Read more
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Replacement top hinge pin for refrigerator doors. Provides the upper pivot point for smooth door swing and proper alignment. Replace if bent or worn.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Seals the front edge of your refrigerator's crisper or pantry drawer pan cover to prevent cold air loss. Replace if worn, cracked, or not sealing properly.
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
This refrigerator ice maker assembly freezes water and automatically ejects cubes into the bin. Replacing a failed unit restores steady, hands-free ice production and helps resolve common ice maker cycling and cube-ejection issues.
The ice maker stopped producing ice. The motor just made a periodic spinning noise and the ice maker never filled with water. I ordered a replacement ice maker and the valve just in case. I just ended up replacing the ice maker, which is just two screws and a plug. A couple hours later, the new Ice maker was making ice as good as new. Read more
Fix frost buildup and inconsistent cooling by replacing a failed defrost heater. Melts ice from the evaporator coil during defrost cycles. DIY repair.
Replaced the heater Read more
Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.
Very simple. Remove old grille (2 screws). Install new grille. Read more
Reduces contaminants and removes chlorine taste and odor for cleaner, fresher water. Replace every 6 months for optimal performance. Verify compatibility.
Made a call for box of 3 new filters & they came in 4 days. Read more
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Refrigerator not cooling or freezer has frost buildup? This defrost thermostat controls defrost cycles. Common DIY fix, typically takes 1 hour.
When I looked on the Appliance Parts Pro website it said the usual fix for a refrig that is not cooling is to replace the defrost thermostat in the freezer. I didn't see how that would keep the refrig from cooling but I figured I would try it. Got the part yesterday ( two days shipping which was great!). I took the panel off the back of the freezer and the coils were all covered in solid ice! it took me an hour with a heat gun to melt the ice. I changed the defrost thermostat and now the... Read more
Replacement shelf assembly that covers the snack/deli drawer in the fresh food section. Replace if cracked, broken, or missing to restore storage space.
Bought one from you. Read more
Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.
Replaced with new parts. Read more
Cup-activated lever that controls ice dispensing on side-by-side refrigerators. Replace if cracked, broken, or unresponsive to restore dispenser function.
This non-adjustable shelf unit mounts permanently inside the refrigerator compartment to provide storage space. Replace if the shelf is cracked, sagging, or the mounting points are damaged and cannot support normal food storage weight.
I ordered the parts from you and put them right on. I had no problem at all very happy with your parts and was amazed at the time it took to get my parts. I will make sure I ordered from you again. Thanks. Read more
Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.
By using my socket set Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.