General Electric Refrigerator Parts

Fix blank displays, inaccurate temperature readings, or unresponsive controls. This control board regulates cooling cycles and monitors sensors. Moderate DIY.

Replaces worn or broken hinge cam riser on the lower door hinge. Restores smooth door lift and closing action. Essential when door sags or grinds.

Fixes refrigerator temperature issues and cooling failures. Replaces faulty control board causing warm compartments or compressor problems. 45-minute DIY fix.

Replace worn refrigerator door gasket to restore airtight seal, prevent warm air entry, reduce frost, and maintain stable temperatures. Verify fit.

Stores chilled water inside your refrigerator for the door dispenser. Replace if cracked, burst, or leaking along the seams to restore proper water supply.

This temperature sensor monitors internal refrigerator temperatures and relays them to the control, helping the unit maintain consistent cooling. Replacing a failed sensor restores accurate temperature regulation and more reliable operation. What it does:

• Measures compartment or evaporator temperature and sends a resistance signal to the control board
• Helps the control modulate compressor and fan run times for proper cooling
• Typical failure signs: sections too warm or too cold, erratic temperatures, or running longer than normal
• Causes inaccurate temperature readings compared to setpoints

• 1 temperature sensor assembly

• Disconnect power before servicing
• Access the sensor in the affected section; release any cover/clip and unplug the connector
• Route the new sensor's wiring like the original and ensure it's fully seated in its holder or clip
• Restore power and allow up to 24 hours for temperatures to stabilize

Fix a warm fridge or freezer not cooling properly. This evaporator fan motor circulates cold air throughout your refrigerator. DIY repair in 30-40 minutes.

This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.

• Drives the ice auger/crusher to feed ice from the bucket through the dispenser chute
• Helps deliver cubes or crushed ice, depending on the control selection
• Common symptoms: no ice dispensing, auger not turning, loud humming or grinding, intermittent or weak dispensing
• Located in the freezer-door dispenser assembly and engages the ice bucket coupler

• Disconnect power to the refrigerator before servicing
• Remove the ice bucket and dispenser trim/panel to access the motor; note wire orientation and fasteners
• Transfer any mounting hardware or coupler from the old motor
• Reassemble, restore power, and test ice dispensing

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

Carries defrost water from evaporator to drain pan in your refrigerator. Replace if cracked, brittle, clogged, or missing to prevent leaks and puddles.

Replace your refrigerator's dispenser drip tray if it's cracked, peeling, discolored, corroded, or worn. Slides into place beneath the water/ice dispenser.

Replace cracked or broken ice bucket guide slides in your refrigerator freezer. Mounts to freezer wall to support and guide the ice bucket assembly.

Base grille that covers the lower front of your refrigerator. Replaces cracked, broken, or missing grilles to protect components underneath.

Forms an airtight seal around your refrigerator door to maintain stable temperatures and prevent frost buildup. Replace when worn, torn, or no longer sealing properly.

Positions refrigerator door components with correct clearance for smooth swinging and level alignment. Replace if worn, cracked, or missing to restore fit.

This ice bucket stores the ice your refrigerator's icemaker produces and keeps it organized and ready to use. Replace a cracked or missing bin to restore proper ice storage and help prevent spills, jams, and contamination.

• Collects and stores ice cubes produced by the icemaker
• Positions under the icemaker so cubes drop cleanly into the bin
• Slides in/out for easy access and smooth operation
• Common symptoms: cracked or warped bucket, ice spilling or jamming, difficulty seating the bin, plastic fragments in ice

• Unplug the refrigerator and switch the icemaker off before servicing
• Remove the old bucket and empty any ice; transfer any reusable parts from the original if applicable
• Align and fully seat the new bucket on the guides/tabs
• Restore power and turn the icemaker back on; allow time to make ice