Hotpoint Parts

I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I do repairs for rental property companies and was inspecting a refrigerator freezer that wouldn't close properly. While onsite at the rental property, I used my smart phone and ordered a new freezer door gasket to replace the inoperable one. I received my order quickly and had the property back on the market for rent in no time. The quick order processing and delivery is what keeps my vendors choosing me over my competitors! Now, I always turn to Appliance Parts Pro for any needed appliance... Read more

Fast delivery, great service Read more

Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more

Replaced the timer Read more

Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more

Once I watched the video on your site about gas line install, it became apparent why the line bent when I raised the lid.. also discovered those two rods have nest to go into and the lid/top now sets down tight as designed ( and as an added bonus, gas smell disappeared during oven use) I ordered the gas lines with the model number, ordered all four …. it was a bit of a chore one came up when site opened I picked it, but did not know if it was the RH or LH etc.. so reading some of your answers... Read more

Replaced the igniter Read more

We replaced both the fresh food door and freezer door gaskets. Old gaskets must have lost their magnetic abilities. Read more

Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?". Read more

Remove and replace Read more

I ordered a new motor through ApplianceParts Pros.com and had the new part within 5 days. The entire replacement took approximately 1 1/2 - 2 hours. The repair was relatively simple and straight forward. By doing the work myself I saved over $250. Originally a GE technician quoted a price of $489 to replace the motor to repair the dishwasher. For that price I could have bought a new dishwasher (Electronix Express $491) but not with all the features of my current appliance. By doing the... Read more

Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more