Hotpoint Parts

The Oven Door Gasket is an OEM replacement part for GE ranges and wall ovens. It provides a secure seal around the oven door to contain heat within the cooking cavity. The gasket is essential for efficient operation as it helps maintain optimal cooking temperatures.

Causes of a bad door gasket can include heat damage over time, warping from repeated door openings and closings, or accidental tears and ruptures. 

Symptoms of a bad oven door gasket include: 

• Excessive heat loss around the door area 
• Inconsistent or inefficient cooking performance
• The door not sealing properly, allowing heat to escape
• Rust or corrosion on interior door parts

This OEM GE part is compatible with GE, Hotpoint, Monogram, and certain Kenmore wall oven models.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Overlay is an OEM replacement part for GE ranges and ovens, designed to provide a clear, durable interface for the appliance's control panel. The overlay is a protective and decorative film that labels each function and control on the electronic control board of your range or oven. It allows users to select settings and modes accurately.

Common causes of a bad overlay include frequent cleaning using harsh chemicals that degrade the material, exposure to high heat or direct sunlight resulting in fading or warping, and physical damage from impacts or scratches that may occur during cleaning or general use.

Symptoms of a bad overlay include:

• Difficulty in selecting the correct settings due to faded or missing labels.
• The appearance of the control panel looks worn or unattractive, affecting the overall look of your kitchen.
• Moisture infiltration into the control panel, potentially causing electrical issues.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Refrigerator and freezer door bar end cap. Used on both the right and left hand side. Color: white. Measures about 2-1/2 inches high by 3 inches deep.

The Hub is an OEM replacement part for GE dishwashers. It is the central mechanism which attaches to the tub and facilitates rotation of the upper spray arm above dishes. 

Causes of a bad hub include wear from years of repeated rotation, accumulation of hard water scale deposits inside moving parts, or accidental impact damage. This reduces proper function over time.

Symptoms of a bad hub include:

• Loud clunking or grinding noises from the center mechanism
• Reduced cleaning performance on upper racks or portions of dishes  
• Dishes showing water spots or soil in sections not adequately rinsed
• Inability to attach or move the upper spray arm assembly smoothly

This OEM GE hub replacement is also compatible with Crosley, and KitchenAid models.

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

The Grill Recess is an OEM part for GE refrigerators. This part collects spills and overflow to keep the dispenser area clean. 

Causes of a bad grill recess can include physical damage from impacts, prolonged exposure to moisture leading to corrosion, or the accumulation of dirt and mineral deposits.

Symptoms of a bad grill recess include:

• Visible cracks or breakage
• Water leakage around the dispenser area
• Difficulty in removing or installing the grill
• Accumulation of water or debris in the dispenser area

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Defrost Thermostat is an OEM part for GE refrigerators. This component monitors the evaporator temperature. It activates warming to defrost the evaporator once the temperature reaches a certain point.

Over time, the defrost thermostat can fail due to electrical issues, exposure to fluctuating temperatures, or general wear and tear. A malfunctioning thermostat can lead to excessive frost buildup, affecting the refrigerator’s cooling efficiency.

Symptoms of a bad defrost thermostat include:

• Excessive frost buildup in the freezer
• The refrigerator or freezer not maintaining the correct temperature
• Water leaks inside the refrigerator
• The defrost heater not activating during the defrost cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement control knob fits the surface burner valve on many ranges and cooktops. It restores smooth on/off operation and flame adjustment when the original knob is cracked, stripped, wobbly, or missing.

• Press-fits onto the valve stem to turn the surface burner on/off and set flame level
• Replaces knobs that are cracked, stripped (spins or slips), loose, melted, or missing
• Helps restore accurate feel and alignment so settings match the dial
• Common signs: knob rotates without engaging the valve or does not stay seated

• Ensure all burners are off and the appliance is cool before servicing
• Pull the old knob straight off the valve stem; do not pry against the control panel
• Align the new knob with the stem flats/notch and press firmly until fully seated
• If the knob won't seat, inspect the stem for debris or damage before reattempting

This oven bake element generates the heat for the Bake cycle. Replace it when the oven won't heat or takes too long to reach temperature to help restore consistent, even baking performance.

• Provides primary heat during the Bake mode
• Common symptoms of failure: no heat in Bake, very slow preheat, uneven or undercooked results
• Element shows visible damage such as blisters, breaks, or burned spots
• Replacing a failed element can restore normal oven operation

• Disconnect power at the breaker; ovens use high voltage
• Remove oven racks and access the element from the oven cavity; note screw locations and wiring
• Move wires to the new element one at a time and ensure snug terminal connections
• Avoid bending the element or overtightening screws; restore power and test Bake

Hi-limit thermostat. L210.

This dial assembly is the labeled control ring used on a washer's control panel. It restores clear cycle selection and secure indexing when the original dial becomes cracked, stripped, or unreadable.

• Provides the printed cycle/setting indicators and aligns with the knob for accurate selection
• Replaces a damaged or missing dial that wobbles, slips, or no longer shows settings
• Helps ensure your chosen cycle is indicated correctly on the panel
• Typical symptoms include a loose dial face, misaligned pointer, or difficulty selecting a cycle

• Disconnect power to the washer before servicing
• Pull the control knob straight off; remove any retaining clip if present
• Release the old dial's locking tabs and lift it away from the panel
• Align the new dial and press to lock in place; reinstall knob (and clip, if used)

The Freezer Fan Motor is an OEM part for GE refrigerators. It is responsible for circulating air within the freezer compartment, ensuring proper cooling and temperature regulation.

Causes of a bad fan motor can include bearing failure due to wear and tear, electrical issues such as shorts or overheating, or simply reaching the end of its operational lifespan.

Symptoms of a bad Freezer Fan Motor can include:

• Inconsistent or inadequate cooling in the freezer
• Excessive frost buildup
• Loud or grinding noises coming from the freezer area
• The refrigerator running constantly or cycling on and off frequently

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Burner Cap is an OEM part for GE gas ranges. This component sits on top of the burner head, dispersing the flame evenly for optimal cooking performance and protecting the burner head from spills and debris.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high temperatures, accidental drops or impacts, and buildup of food residues or cleaning chemicals that can erode the surface over time.

Symptoms of a bad burner cap include:

• Uneven flame distribution or yellow flames
• Difficulty in igniting the burner
• Visible cracks, chips, or warping on the cap
• Poor cooking performance due to inconsistent heat

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This idler pulley keeps tension on the dryer drum belt so the motor can spin the drum smoothly. Replacing a worn pulley can quiet squealing and restore consistent tumbling.

• Maintains proper belt tension so the drum turns under load
• Free-spinning pulley reduces friction and belt wear
• Common symptoms of failure: squealing/chirping noises, drum won't turn, belt slipping or fraying, burning rubber smell
• Helps prevent the belt from jumping off the motor or drum

• Disconnect power; for gas dryers, shut off the gas supply
• Access typically requires removing the top/front panel and releasing belt tension to remove the drum
• Transfer any spacers/retainer from the old pulley to the new one; the pulley spins freely before reassembly
• Route the belt per the model's diagram and check belt alignment/tension before test run

This button tree is the group of selector buttons behind the control panel. It restores reliable button action so you can choose cycles and options when keys stick, feel mushy, or stop responding.

• Provides the push-button interface for cycle and option selections on the control panel
• Helps address unresponsive or intermittent keys
• Resolves sticking or jammed buttons
• Restores proper alignment and tactile feel

• Disconnect power to the appliance before servicing
• Remove the console/control panel to access the button tree
• Seat the new button tree so each button aligns with the control board switch positions and the overlay
• Handle the user interface board and wiring gently; do not force clips or tabs