Jenn-Air Parts

Ordered new gasket seals and had someone install them, Installed one prior myself and it was very difficult to heat and stretch and wrap doors. Ended up gouging my cabinet when stretching the seal . Leave for professionals and even they struggled. Tight now and working great. Read more

Every six months I change my refrigerator filter. I purchased a new filter (UKF8001) and installed it just like I've done many times before. This time, when I first used the water dispenser, I got a horrible sound (kind of like a jack hammer/vibration) followed by very little water flow. I disconnected the new filter and reinstalled the old filter, thinking maybe I got a bad filter. No improvement. I removed the filter and put the bypass cap on and everything returned to normal. Since... Read more

Replaced the ice dispenser motor( very easy only 4 screws and a power plug. I also replaced the auger drive shaft and rubber grommet Read more

• Freezer not defrosting

After we moved into our new home, we realized that the freezer was very cold and the fins were frosting over, and the refrigerator wasn't cold. We had to take it apart and manually defrost it about once every 8 to 10 days. After research online, we found Appliance Parts Pros videos, which clearly explained how to fix it ourselves, a savings of at least $1,000 or more, since a new one of this size would have been in the arena of $1,200 to $2000. We ordered the three most likely parts to be bad,... Read more

I got on appliance parts pros website, looked up my model number. Using their diagrams I found my part. Ordered it and replaced it, just like the new one. Read more

Replaced them but Jennair knobs are really cheap and I’m sure I’ll have to keep replacing them. Sad that such an expensive appliance has such cheap knobs. Read more

Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference. Read more

Easy project. 6-year-old appliance. If one is failing replace all 4. The plastic race that holds the bearings becomes brittle and breaks dropping the bearings into the dishwasher tub. Total project time from assembling tools, protecting the hardwood floor, removal, and installation was less than 2 hours. 1) Turn off power to the appliance. 2) Remove 2 mounting Phillips screws holding dishwasher in the cabinet. 2) use a 1/4” nut driver to remove the 2 screws holding the bottom plate from... Read more

The lightbulbs were a problem for me as I did not know if they were 12 V or 120 V. But the interactive parts diagram on the website was very helpful and allowed me to order the correct bulbs very rapidly(120V is correct). They were very easy to change out except for the fact that I needed to have my 12-year-old son do part of it since his hands are smaller than mine.(and it is always good for sons to work with dads even on small projects like this.) The cooking element was also amazingly easy... Read more

Found the correct USA made OEM part from Appliance Pros, and installed it on my new Dishwasher. The use of this correctly manufactured Adapter prevented any damage to the threads of the dishwashers inlet solenoid valve which is made of a plastic material. If I had forced the after market adapter onto the solenoid valve instead of ordering the OEM adapter; it would have ruined the threads on the plastic solenoid valve resulting in the need to purchase a very expensive replacement valve. ... Read more

Replaced condenser fan but that was not it. I need ice maker fan Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

Fixed the door seal myself with parts from Appliance Pro. I watched a few You tube videos and it was a half hour job. Your parts arrived within 24 hours. Great delivery! Wow that was fast and matching parts and model numbers was easy using the ordering on line site. Thank you. Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more