Kenmore / Sears Dryer Parts

Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more

Replaced control board. Did not need Control Thermistor in my case, but I'm keeping it as backup. Got the Drum Belt just in case it breaks on me since the dryer is aging. To replace control board: Disconnect power and pull dryer away from wall. Take 2 black screws on the back off to remove the top lid. Remove 2 screws on top that hold the control interface on. Remove 2 screws on the bottom backside of the control. Pull out control panel and pull off terminal connections and push to remove... Read more

• No heat or not enough heat

I replaced the heating element supplied by AppliancePartsPros.com. It took me longer than the estimated 30 minutes to an hour cited in the good instructional video. A few things took more time than I had expected: 1. Removing the top of the dryer unit resulted in my breaking off the three plastic tabs that is used to anchor the top to the structure below. In putting it back together, I didn't need those three tabs as the side plastic structure on each side will secure the top to the... Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more

Had to purchase a new filter as the felt does not feed back into the ridge in the filter. It seems to me that the felt should not pull out so easily. My dryer isn't even a year old so I think this is a design failure. But the new filter works great and hopefully we won't have this problem again. Thank you for your prompt service! Read more

Replaced door strike and door latch Read more

My husband took the panel off. Check different things. Talked to someone at Appliance Parts. He told him some things to test. It was the timer that needed replacing. So happy to have my dryer working again! :) Read more

I looked on Appliancepartspros.com, it helped me diagnose the problem, told me what parts to buy and showed me a video of how to fix it. Therefore I saved $150 by not having to call a repair shop. Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

Remove and replace Read more

I tried to buy a new refigerator, but strangely none of the major stores had anything I wanted in stock. The earliest delivery date for a new unit was over a month away. At that I decided to try and keep this one running. I did online research into common refigerator problems. I found the cooling coils in the freezer were covered in a block of ice and frost. The refigerator was not going through a defrost cycle. With a hair dryer I thawed out the coils. The refigerator worked fine for... Read more

Replaced blower belt and nut as per your You tube video. Read more