Kenmore / Sears Parts

This wiring harness assembly routes power and signals between the appliance control and electrical components so the unit operates reliably. It replaces a damaged or burnt harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Connects controls, switches and motors to the main power and control board
• Restores interrupted circuits that can cause intermittent operation or component failure
• Helps resolve symptoms like lights, fans or motors not running or responding
• Replaces frayed, melted or corroded wiring that creates shorts or open circuits

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle connectors by the plug bodies; avoid pulling on wires
• Route and fasten the harness exactly as the original to prevent chafing or heat exposure

This push-button door switch detects when the appliance door is closed and allows normal operation. It replaces a worn or failed door interlock to restore reliable start/stop response and user safety. What it does

• Acts as the door-closed sensor that permits the appliance to start when the door is latched.
• Interrupts power to drive/heating circuits when the door opens, preventing operation with an open door.
• Stops intermittent starting or running caused by a faulty or stuck switch.
• Helps resolve symptoms like the appliance not starting, stopping mid-cycle, or not responding to door closure.

• One door switch (push-button type)

• Disconnect power (unplug or shut off breaker) before accessing electrical components.
• Remove door trim or control panel as needed to access and replace the switch; keep track of screws and clips.
• Verify switch operation with a continuity meter before and after installation.

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rocker Switch is an OEM part for Whirlpool refrigerators. This switch is responsible for controlling the operation of your refrigerator's ice maker, allowing you to turn it on or off as needed, providing you with easy control over the ice maker.

A bad switch can occur due to regular wear and tear, electrical issues, or physical damage. If you notice symptoms such as an unresponsive switch, inability to turn the ice maker on or off, or inconsistent ice production, it may be time to replace the rocker switch.

Symptoms of a bad switch include:

• Unresponsive switch
• Inability to turn the ice maker on or off
• Inconsistent or inadequate ice production

Regain control over your Whirlpool refrigerator's ice maker by replacing the faulty or malfunctioning on/off rocker switch with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This electrical switch restores reliable on/off control to the designated circuit in your appliance. Replacing a worn or stuck switch helps ensure lights, fans, or motors operate only when they should. What it does

• Opens and closes an electrical circuit when actuated
• Helps correct issues like a light that won't turn on/off or a component that won't run or won't stop running
• Resolves intermittent operation caused by worn contacts or a loose/broken actuator
• Addresses signs such as melted/discolored terminals or an unusually loose/tight switch feel

• 1 switch

• Disconnect power to the appliance before servicing (unplug or switch off the circuit breaker)
• Access the switch location per your model's service information
• Photograph wire positions and transfer connectors one at a time to the new switch; do not force terminals
• Secure the switch, reassemble, restore power, and test operation

The Surface Element Control Switch is an OEM part for Frigidaire ranges. It is responsible for regulating the heat output of the surface elements on your range, allowing you to adjust the temperature for different cooking needs.

A bad surface element control switch can be caused by wear and tear, electrical issues, or component failure. When the control switch becomes faulty, it can result in issues such as the surface elements not heating up, inability to adjust the temperature, or inconsistent heat output.

Symptoms of a bad surface element control switch include:

• Surface elements not heating up
• Inability to adjust the temperature of the elements
• Surface elements heating unevenly or inconsistently

Replace your faulty surface element control switch with this genuine OEM Frigidaire part to restore your range's surface elements. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a black rocker switch used to control a function on compatible ranges/cooktops. Replacing a worn or inoperative switch restores positive on/off control and reliable operation of the connected feature.

• Controls an appliance function (such as a light or igniter circuit) with a single on/off action
• Common failure signs: switch won't stay on, no response when toggled, intermittent operation, or physical damage/discoloration
• Direct-fit replacement designed for the original switch location
• Helps restore safe, predictable control to the appliance

• Disconnect power and, if applicable, shut off gas before servicing
• Access is typically from the control panel; retain orientation of wires and note terminal positions
• Transfer wires one at a time to the new switch to avoid miswiring
• Inspect connectors for heat damage; replace damaged terminals before reassembly