Kenmore / Sears Washer Parts

I ordered the male and female door latching parts. Read more

Watched the video a few times for door boot seal replacement. It was a lot of help! The spring is the hardest to replace and I did enlist the help of my wife. Everything went back on great. If you have to replace the front panel (with the buttons) be mindful that the buttons are spring loaded and will come out. I did not lose any and it went back together just fine. A little touch up paint on the washer and it all looks brand new and works great. And the parts came in quicker than... Read more

• No heat or not enough heat

I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more

We started getting the F06 code when on the normal cycle it was time to Rinse/Spin, pointing to a speed/tachometer issue on the motor. After several attempts of unplugging from power and restarting the cycle it would eventually start working for the rest of the laundry session. The Whirlpool technician after a brief look on the underside determined it was the motor and had to be replaced, even tough all troubleshooting tests on the motor were ok. I insisted that the probability was much higher... Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more

Once you tilt the washer and prop it against something it's a pretty straight forward and easy fix. If you watch the instructional "How-to" video beforehand, the repair should take between 30 to 60 minutes. It all depends on your skill level and if everything goes smoothly. Make sure you have all the proper tools, grease and blue thread lock at the ready to help you move this repair along faster. This repair was in conjunction with replacing the motor position sensor. I didn't know I needed a... Read more

At first, I thought, maybe I should just get a new washing machine. After all, it is almost 20 years old! I couldn't bring myself to do that and said to myself, let me see if I can figure out what parts I need and see if I can find a video that tells me how to do it and see how hard it is. I’ve never attempted appliance repair before. After figuring out what the most likely parts were, I ordered the water level switch and agitator cam repair kit - I figured for $10 more, I might as well... Read more

Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more

• Will not stop filling with water
• Will not fill with water

Reviewed troubleshooting tips and identified problem as "water level switch". Watched repair video, which was very helpful. Ordered part on a Sunday, which arrived the following Tuesday. Repair was easy the fix was successful. Read more

Replace the Mainboard control and push the start button. Read more

I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more