Kenmore / Sears Washer Parts

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

I also noticed one of the two water recirculation outlets near the front door was no longer spraying water. When I took it all apart, I found that these two tub water recirculation outlets are both connected to the pump.. one was clogged. The impeller on the drain pump was no longer spinning with the motor.. looks like it was worn on the inside.. when I took the pump apart it was full of scale. I could have just ordered the motor...but I figured I would replace the entire assembly as I also... Read more

I noticed my 5-year-old Samsung, front-loading washing machine started to sound like my kids were using it as a drum kit. I immediately checked it out and the stainless drum was wobbling so badly that I just took it for an unbalanced load of clothes. My gut was telling me that something was wrong because I had not remembered the machine being so loud before. I removed the clothes from the washer and I ran it empty to confirm my suspicions: the wobble was still there. I would say it had a 2"-3"... Read more

REMOVED BACK PANEL, USED PLYERS TO REMOVE CLAMP, PULLED OLD HOSE OFF, REVERSED PROCEDURE TO INSTALL NEW HOSE. TOTAL TIME ABOUT 10 MINUTES. Read more

I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more

I repaired it myself. I viewed each video on YouTube from AppliancePartsPros.com. I saved 200.00 and my washing machine runs like a top. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

This part was the perfect fix for my broken door hinge on my LG front loading dryer. I watched a video on YouTube of a hinge replacement of a similar front loading Samsung dryer. I needed a little help from my son holding the door glass and plastic in place while re-attaching the door to the hinge, but it was an easy repair. Read more

My appliance is a Kenmore, and even though the video mentioned lots of other brands, it showed the exact same problem I was having. My dispenser motor just spun and spun, never stopping at the various positions it was apparently supposed to. Then it would trip the F30 code. The part description again mentioned these other brands but did say in fine print it fits some Kenmore products. I could tell visually from the video the part was the same as on my washer so I felt confident the part... Read more

This hose did not just attach to the back of the washer--that would have been too easy. This hose went into the back of the washer, under the tub & attached to the pump at the front of the washer. Both the back & front of the washer had to be removed to access the hose. Luckily the crack was at an external spot where it was easily seen; unluckily my husband was out of town at the time & I had to take the washer apart & put it back together. Actually it was not that hard. Before I took the... Read more

• Will not stop filling with water
• Will not fill with water

At first, I thought, maybe I should just get a new washing machine. After all, it is almost 20 years old! I couldn't bring myself to do that and said to myself, let me see if I can figure out what parts I need and see if I can find a video that tells me how to do it and see how hard it is. I’ve never attempted appliance repair before. After figuring out what the most likely parts were, I ordered the water level switch and agitator cam repair kit - I figured for $10 more, I might as well... Read more

I looked at a video on YouTube and followed the instructions. Read more

I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more

I called parts pro and they had my part and sent it right to me I am soooooooo happy with this company they are amazing. I only ordered 1 baffle and now I'm calling them to order the other 2 baffles. Thank you so much for your help and service. Read more

An online search for LG washing machine parts came up with a repair video from Appliance Parts Pros. I watched the video. It was very well done, very detailed, and took you step by step through the entire process to replace the tub bearings and the spider, from start to finish. After watching the video, I realized this repair was well within my abilities. No specialized tools were needed. I ordered the parts from Appliance Parts Pros, and all items were in stock and delivered within a couple... Read more

I tube what could be the cause. Took apart the washer and ordered the parts. Put parts in. Read more