Kitchenaid Gasket & Seal

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Gasket-FIP  is an OEM part for Whirlpool refrigerators, ensures an airtight seal around the door, preventing cold air from escaping and warm air from entering. This component contributes to the refrigerator's energy efficiency and cooling effectiveness, maintaining the optimal internal temperature to keep your food fresh longer. 

Causes of a bad Gasket-FIP can range from normal wear and tear, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures.  

Symptoms of a bad Gasket-FIP include:

• Noticeable gaps between the gasket and the refrigerator door or frame
• Condensation or frost buildup near the door edges
• The refrigerator working harder to maintain its internal temperature, potentially leading to increased energy bills
• The door not closing as smoothly or firmly as it should

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Freezer Door Gasket is an OEM replacement part for Whirlpool bottom-mount refrigerators. This white freezer door gasket is responsible for maintaining a tight air seal around the entrance to the freezing compartment. It helps retain cold air inside and prevents warm drafts or humidity from affecting food freshness and freezer efficiency. 

Symptoms of a bad freezer gasket include: 

• Difficulty keeping consistent temperatures inside the freezer section
• Visible moisture, frost, or condensation around the door perimeter
• Noticeable warm air infiltration reducing cooling performance

Causes of freezer gasket failure involve regular opening and closing of the door. Over time, the flexible material breaks down from continuous use exposing it to changing environmental temperatures. Physical damage from overstuffing shelves or slamming the door can also prematurely damage the gasket.

This OEM replacement is also compatible with some KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

The Tub Gasket is an OEM replacement part for Whirlpool washing machines. This gasket forms a crucial seal between the washer tub and the cabinet, both preventing water leaks and reducing noise and vibration. 

Causes of a bad tub gasket can include cracks, tears, or compression failures due to age, use, or impacts over time. Gaskets can also degrade with chemical exposure.

Symptoms of a bad tub gasket include:

• Water leaks from around the tub and cabinet interface 
• Excessive noise or vibration during spin and agitation cycles
• Reduced washer balance resulting in thumping or off-center loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This panel bag assembly seal creates a secure, flexible gasket between the appliance panel and bag assembly to help maintain proper sealing and prevent leaks. It restores the intended fit for reliable operation. What it does:

• Seals the junction between the bag assembly and the panel to limit air or dust escape
• Helps maintain suction/containment performance when the bag is installed
• Reduces vibration or rattling by providing a snug fit
• Addresses common symptoms like visible gaps around the bag panel, escape of dust/debris, or panel movement

• One panel bag assembly seal

• Disconnect power and remove any batteries before beginning service
• Remove the panel or bag assembly per the appliance service instructions to access the seal
• Replace the old seal with the new seal, ensuring it seats fully in the channel or mounting groove
• Inspect surrounding clips and fasteners and reassemble carefully; test operation after reinstallation

Replace a worn or torn refrigerator door gasket to restore a tight seal and help maintain proper cooling. This exact-service door gasket in Apollo Gray fits the door edge and compresses to keep cold air in and warm air out. What it does:

• Seals the refrigerator/freezer door to help maintain internal temperature and energy efficiency.
• Prevents warm, humid air from entering and forming frost or condensation inside the compartment.
• Helps eliminate drafty edges, clicking door behavior, and uneven cooling near the door.
• Restores proper door closure when the original gasket is cracked, flattened, or damaged.

• High-level replacement: remove the old gasket, align the new gasket in the door channel, and press into place; follow factory warm-water or heat-stretch procedures if required by the OEM.
• Inspect the door flange and mounting channel for damage or debris before installing the new gasket.
• For best seal, allow gasket to settle for 24 hours and check for gaps; use care when heating or stretching to avoid distortion.
• Disconnect power only if instructed by the appliance manufacturer for your specific model.

This sink flange seal is a rubber gasket that creates a watertight seal between the sink and drain flange to help prevent leaks and water damage. Use it when the flange seal is cracked, flattened, or leaking. What it does:

• Seals the gap between the sink and drain flange to stop water from leaking under the sink.
• Helps prevent sink-edge water pooling and slow drainage caused by a failed seal.
• Reduces chance of odors from trapped water beneath the flange by restoring a tight seal.
• Restores proper fit when replacing a corroded or worn sink flange assembly.

• One sink flange seal (rubber)

• Turn off water supply and disconnect drain components before replacing the seal.
• Remove the drain flange assembly, clean mating surfaces, then seat the new seal evenly.
• Avoid stretching or cutting the seal; replace it if damaged or misshapen.

This replacement gasket seals the appliance door to help maintain proper temperature and improve efficiency. It restores the original sealing surface to reduce leaks and keep the compartment at the intended temperature. What it does:

• Creates a tight seal around the door to help prevent air leakage
• Helps maintain consistent internal temperatures for proper performance
• Reduces frost buildup and energy loss caused by a compromised seal
• Addresses symptoms like warm spots near the door, excess frost, or cycling issues

• Disconnect power (and water if applicable) before starting any repair
• Remove the door or access panel for easier replacement
• Fit the gasket into the channel evenly; avoid stretching or twisting the material
• Inspect the mounting flange and surrounding surface for damage before installation

This replacement door seal restores the fridge door's airtight closure to help maintain proper cooling and reduce energy loss. Designed to fit original-style openings, it keeps cold air in and warm air out for reliable food preservation. What it does:

• Creates an airtight seal along the refrigerator door edge to maintain consistent interior temperatures
• Helps prevent frost buildup and reduces strain on the compressor by improving efficiency
• Addresses common symptoms like warm spots near the door, excess frost, or a door that won't close snugly
• Fits into the door channel and compresses when the door is closed to form a tight barrier

• Replacement may require door removal and trim manipulation; follow your model's service instructions
• Inspect the door channel and mounting flange for damage or debris before installing the new seal
• Warm the seal slightly to ease installation and ensure a uniform fit; avoid open flames or excessive heat
• Test the door for a consistent seal after installation and make any hinge/strike adjustments if needed

This is a replacement freezer door gasket that seals the freezer compartment to help maintain cold temperatures and reduce frost buildup. It restores a tight seal for better efficiency and food preservation. What it does:

• Creates an airtight seal around the freezer door to keep cold air in and warm air out
• Helps reduce frost and ice buildup inside the freezer
• Supports consistent internal temperatures for safer food storage
• Can improve compressor run cycles by preventing air leaks

• One freezer door gasket as shown

• Check the door and cabinet mating surface for debris or damage before installing
• Gasket edges may need gentle warming to fit snugly; avoid overheating
• Inspect and replace any worn door screws or retainer strips if present for a proper seal
• Disconnect power and follow appliance safety guidelines before performing repairs