Kitchenaid Igniter

Amperage range 3.2 to 3.6

This top burner igniter is a genuine Whirlpool part, sold individually. This top burner igniter can be used as a replacement part in a gas range. This part fits into the surface burner orifice holder to connect to the spark module such that the gas can be turned on to heat up the burner.A top burner igniter might have to be replaced at some point in the lifespan of a gas range. A top burner igniter can be subject to damage if the connection between the igniter and the spark module is severed or is malfunctioning. The primary symptom of a malfunctioning top burner igniter is a gas burner that will not start or ignite properly. If this occurs, the top burner igniter should be removed and replaced with this genuine OEM replacement part before using that burner of the gas range again.This is an OEM part sourced directly from the manufacturer. This top burner igniter is compatible with the following appliance brands: Whirlpool, Amana, Jenn Air, KitchenAid, Ikea, and Maytag.

This surface burner spark igniter creates the electric arc that lights the gas flame on your cooktop or range. Replacing a worn or cracked electrode restores reliable ignition and helps resolve hard-to-light burners and intermittent sparking.

• Provides a high-voltage spark at the surface burner to ignite gas
• Mounts to the orifice holder beneath the burner head
• Failure symptoms include burner not lighting, needing a match, or intermittent/weak spark
• Common issues: chipped/cracked ceramic insulator or damaged terminal/lead

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove grates, burner caps, and heads to access the orifice holder
• Transfer the ignition lead, install the new electrode, and route the wire away from heat and sharp edges
• Ensure the tip is positioned near the burner as designed; verify spark and ignition before reassembly

This surface burner ignitor creates the spark that lights gas at a cooktop/range burner. Replacing a worn or cracked electrode restores quick, reliable ignition and helps prevent repeated clicking or failed lighting at that burner.

• Generates a high-voltage spark at the burner to ignite gas
• Common fix for a surface burner that won't light or takes many clicks to light
• Addresses visible cracks, chips, or burned ignition tip on the electrode

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Handle the ceramic insulator carefully; avoid touching the electrode tip
• Note wire routing and ensure a secure connection to the harness/spark module
• Position the electrode correctly relative to the burner head for consistent ignition

This is the surface burner igniter electrode for gas cooktops/ranges. It creates the spark that lights the surface burner, restoring reliable ignition and eliminating the need for manual lighting.

• Generates the spark to ignite the surface burner flame
• Helps address issues like no spark at a burner, intermittent ignition, or clicking without lighting
• Can resolve weak/damaged electrode tip causing poor spark
• Correct arcing to ground near the burner head

• Disconnect power and shut off gas before servicing
• Handle the ceramic insulator carefully to avoid cracking
• Ensure proper positioning and gap to the burner cap per service guidance
• Route and secure the lead away from heat and sharp edges; reconnect firmly to the spark module harness

This surface burner spark electrode creates the spark that lights the gas on your cooktop or range. Replacing a worn or cracked electrode helps restore quick, reliable ignition and can reduce excessive clicking at the affected burner. What it does:

• Generates a high-voltage spark at the burner head to ignite gas
• Helps ensure fast, consistent ignition for the specific burner
• Common symptoms can include no spark/no light at one burner, weak or intermittent sparking, or continuous clicking from a damaged/contaminated insulator
• For the surface burner ignition circuit

• 1 spark electrode

• Disconnect power and shut off gas before servicing; allow the cooktop to cool completely
• Remove burner cap and head to access the electrode; note wire routing and connection
• Transfer/reuse any mounting hardware; avoid stressing or cracking the ceramic insulator
• Align the tip to the burner per service information and ensure all connections are secure before restoring power and gas

Electrode that produces the ignition spark for gas ovens and ranges, restoring reliable burner lighting. Replace a damaged or worn electrode to stop repeated clicking, weak sparks, or burners that fail to light. What it does:

• Delivers the spark at the burner to ignite gas during startup.
• Common symptom fix: oven/range burners that won't light or that click continuously without producing a flame.
• Use when the electrode is cracked, corroded, or the ceramic insulator is damaged.
• Works as part of the appliance's ignition system alongside the spark module/igniter wiring.

• Turn off power and gas supply before beginning any service.
• Avoid touching or chipping the ceramic insulator; handle the tip carefully.
• Reconnect wiring exactly as removed and secure the electrode in the original orientation.

This surface burner spark electrode creates the spark that lights the gas on your range or cooktop. Replacing a worn or cracked electrode restores reliable ignition so burners light quickly and consistently when you turn the knob.

• Produces a high-voltage spark at the burner to ignite the gas flame
• Helps resolve: burner won't light, no or weak spark at that burner, needs manual lighting, intermittent ignition
• Damage or contamination on the ceramic insulator can prevent proper arcing
• Direct replacement for the failed electrode at the affected burner

• Disconnect power and shut off gas supply before servicing
• Allow unit to cool completely
• Remove burner cap and head to access the electrode; transfer mounting hardware if reused
• Handle the ceramic insulator carefully; reconnect lead securely and align the tip near the burner head as originally positioned

This oven burner supplies the bake flame in a gas oven, restoring consistent heat for baking and roasting. Replace a damaged or corroded burner to help recover even cooking and reliable ignition. What it does:

• Produces the primary bake flame for the oven cavity so food cooks evenly.
• Replaces a warped, cracked, or heavily corroded burner that can cause weak or uneven heating.
• Can resolve symptoms such as the oven not reaching temperature, uneven baking, or a burner that won't light reliably.
• Works with the oven's ignition and gas flow system; proper flame appearance is important for safe operation.

• Turn off gas supply and electrical power to the appliance before beginning any service.
• Remove oven racks and access panels to reach the burner; retain all fasteners.
• Inspect and clean the burner ports and ignition area during replacement; avoid bending or damaging the burner ports.

The Surface Igniter is an OEM replacement part for Whirlpool gas ranges. It is responsible for generating the spark needed to ignite the gas, ensuring a consistent and controlled flame for cooking.

Symptoms of a bad electrode igniter include:

• Burner not igniting
• Weak or intermittent sparks
• Clicking sound without ignition

A faulty or worn-out electrode igniter can occur due to normal wear and tear or accidental damage. If you notice issues such as the burner not igniting, weak or intermittent sparks, or a clicking sound without ignition, it may be time to replace the electrode igniter.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Surface ignitor restores the ignition spark to a gas range surface burner so the burner can light reliably. Use this direct replacement when a burner produces weak sparks or won't ignite. What it does:

• Generates the spark that ignites gas at a surface/burner assembly.
• Replaces a cracked, worn or non-sparking electrode to restore ignition.
• Commonly used when a burner clicks but does not light or produces intermittent sparks.
• Works as the single electrode component in a surface burner ignition assembly.

• Turn off electrical power and gas supply before service.
• Handle the ceramic tip carefully — avoid touching or bending the electrode.
• Ensure proper connection of the ignitor's wire and correct seating in the burner assembly.

The Surface Ignitor is an OEM part for Whirlpool ranges and cooktops. This component is responsible for generating the spark needed to ignite gas burners on the cooktop or oven pilot light.

Causes of a bad Surface Ignitor can include wear and tear over time due to repeated use during ignition. Physical damage is also possible.

Symptoms of a failed surface ignitor include:

• Inability to ignite any gas burners
• Repeated sparking sounds but no ignition
• Yellow burner flames instead of blue

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This single surface burner spark electrode generates the spark that lights the gas on your cooktop or range. Replacing a worn or cracked electrode restores reliable ignition and reduces "click with no flame" at that burner.

• Creates a high-voltage spark at the burner to ignite gas
• Positions the spark at the burner head via a ceramic-insulated tip
• Common symptoms: burner won't light, no spark at that burner, or intermittent ignition
• Visual clues of failure can include cracked/chipped porcelain or a burned electrode tip

• Disconnect electrical power and shut off gas supply before servicing
• Allow the appliance to cool; remove burner cap/head to access the electrode
• Seat the ceramic insulator fully and position the tip correctly near the burner
• Reassemble and test ignition before finalizing the repair

This igniter top is the spark electrode that produces the spark to light a gas cooktop burner, restoring reliable ignition for safe cooking. It replaces the worn or damaged electrode that fails to spark or lights intermittently. What it does:

• Sends the spark to ignite the burner when the control is turned on.
• Commonly used when burners click but do not light or flame is slow to ignite.
• Helps stop continuous sparking caused by cracked or misaligned electrodes.
• Works with the burner cap and gas valve to ensure consistent ignition.

• One igniter top (spark electrode) as shown

• Disconnect power and shut off gas supply before attempting replacement.
• Handle the ceramic insulation carefully to avoid cracking; inspect wiring and connectors for damage.
• Verify correct part number and fit with your appliance diagram before ordering.

This surface igniter is the replacement spark electrode used on gas cooktop burners to create the spark that lights the burner. It restores reliable ignition so burners light when you turn the control knob. What it does:

• Produces the spark that ignites the gas at a surface/burner element
• Replaces a cracked, worn, or non-sparking electrode
• Common fix for burners that click but won't light or that fail to spark
• Works with the existing electrode wiring and mounting location

• Disconnect power to the range and turn off the gas supply before starting
• Handle the ceramic tip gently to avoid chipping; do not touch the tip with bare hands
• Confirm correct orientation and secure mounting; match wiring to original connections

This surface burner igniter creates the spark that lights a gas cooktop or range burner. The attached wire lead simplifies hookup and helps restore quick, dependable ignition when a burner won't light or only lights intermittently.

• Generates a high-voltage spark at the burner to ignite gas
• Restores reliable burner lighting and consistent flame startup
• Common symptoms: burner won't ignite, no visible spark, intermittent lighting, or a chipped/cracked ceramic insulator
• Replaces a worn or damaged electrode to eliminate the need for manual lighting

• Disconnect electrical power and shut off gas before servicing
• Allow the cooktop/range to cool; handle the ceramic tip carefully to avoid damage
• Match the igniter position/orientation to the original for proper spark at the burner
• Route the lead away from sharp edges and heat; make a secure connection to the harness, then test for spark before reassembly