Kitchenaid Spring Parts

Replacement spring kit that restores proper tension and balance to appliance doors and lids, helping them open and close smoothly and stay in position. Use this kit to replace worn or broken springs that cause sagging or noisy operation. What it does:

• Replaces worn or broken door/lid springs to restore proper tension and balance.
• Helps the door or lid open and close smoothly and remain in the desired position.
• Reduces sagging, bouncing, slamming, and related noise caused by failed springs.
• Prevents additional wear on hinges and closures by restoring correct alignment and support.

• Disconnect power (and water, if applicable) before starting any repair; follow all safety instructions in the appliance manual.
• Support the door or lid during removal and installation to avoid pinch or crush injuries.
• Use proper hand protection and tools; keep small fasteners organized to avoid loss.

This handle spring restores tension to the door latch handle so the dishwasher door latches securely and the handle returns to position. Replace a worn or broken spring to address loose handle feel or doors that pop open during a cycle. What it does:

• Provides return tension for the door latch/handle mechanism
• Helps keep the door closed and latched during operation
• Restores proper handle feel and return action
• Common symptoms include a loose or floppy handle, door not latching or starting, or door opening mid-cycle

• 1 spring

• Disconnect power at the breaker and shut off water before servicing
• Remove inner door panel screws to access the latch area; support the outer panel
• Note spring orientation and attachment points before removal; transfer the new spring to the same tabs/holes
• If your latch uses two springs, replace both for even tension; test latch operation before reassembly

This replacement spring restores the correct tension and return action for its connected mechanism so your appliance operates smoothly. Install it to replace a broken or fatigued spring and resolve weak, inconsistent, or non-returning movement. What it does:

• Provides tension so linked parts move and return to their proper position
• Helps keep mechanisms aligned and operating smoothly
• Replaces stretched, broken, or missing springs that cause poor operation
• Common symptoms: part won't return or stay in place, weak/sluggish action, rattling or rubbing noises

• 1 spring

• Disconnect power before servicing; shut off water or gas if applicable
• Note the original spring routing and orientation; take a quick photo before removal
• Control spring tension during removal/installation to avoid snapback; wear cut-resistant gloves and eye protection
• Use suitable pliers/spring tool and inspect adjacent brackets or links for wear while reassembling

This replacement container spring helps restore proper tension and support for the container assembly, so the container stays secure and operates smoothly. Ideal when the original spring is worn, stretched, or broken. What it does:

• Provides tension to hold the container or bin in its intended position
• Replaces worn or broken springs that cause slipping or poor engagement
• Stops rattling or shifting caused by a weakened spring
• Helps the container latch, release, or return smoothly during use

• Basic hand tools may be required; follow the appliance's service manual for access and removal
• Disconnect power (and water if applicable) before servicing to prevent injury
• Handle small parts carefully to avoid pinching; springs can store tension

This genuine OEM return spring restores proper return/tension for the appliance component it connects to, helping controls, latches or hinges snap back into place. Replacing a worn spring can stop sticking, sagging or failed return action. What it does:

• Provides tension to return a lever, latch or door component to its resting position
• Restores crisp return action when a control or hinge feels loose or fails to snap back
• Helps reduce rattling or intermittent contact caused by a weak or broken spring
• Functions quietly once replaced, improving normal operation of the affected mechanism

• Disconnect power and gas before servicing; follow appliance-specific safety instructions
• Springs can be under tension — use proper tools and caution to avoid injury or part damage
• Compare the old spring to the new one for correct length and end type before installation

This replacement door tension spring restores proper door balance and closure on compatible Whirlpool appliances, helping the door stay aligned and close securely. It's a direct-fit repair part when the existing spring is worn or broken. What it does:

• Provides counterbalance tension so the appliance door opens and closes smoothly
• Prevents the door from sagging, sticking, or not staying fully closed
• Reduces excess strain on hinges and latch mechanisms caused by a weak spring
• Helps eliminate rattling or uneven door movement that can occur when springs fail

• One replacement door tension spring

• Disconnect power and empty the appliance door area before starting any repair
• Use caution: springs are under tension—wear safety glasses and gloves
• Typical install requires basic hand tools; follow OEM diagram for correct routing and attachment

This replacement tension spring restores proper tension and movement for the linked assembly, helping components return to position and operate smoothly. Designed to match the original spring's shape and function for reliable performance. What it does:

• Provides return tension for moving parts so doors, levers, or linkages operate correctly
• Helps maintain correct alignment and prevents sagging or binding
• Replaces worn or stretched springs that cause sluggish or uneven operation
• Common symptom: assembly won't return to its resting position or feels loose

• One tension spring

• Disconnect power (and water if applicable) before beginning any repair
• Use care handling springs under tension; wear eye protection
• Remove any retaining clips or brackets in the order shown in the service diagram

This tension spring restores proper movement and tension for the appliance component it secures, helping the part operate smoothly and reliably. It's a simple replacement that fixes common issues caused by worn or broken springs. What it does:

• Provides tension to hold or return a moving component to its correct position
• Helps stop sagging, slipping, or loose operation of doors, latches, or levers
• Can reduce rattling or unusual noises caused by a failed spring
• Restores normal mechanical action when the original spring is stretched or broken

• Disconnect power to the appliance before starting any repair
• Springs can be under tension—use appropriate tools and wear eye/hand protection
• Compare the new spring to the old one for length, coil size, and end fittings before installation

This door spring counterbalances the door so it opens smoothly and doesn't drop. Replacing a fatigued or broken spring restores proper door feel and helps protect hinges and related components from excess strain.

• Provides the tension that balances the door during opening and closing
• Helps prevent the door from slamming or falling open too quickly
• Replaces a stretched, weakened, or broken spring
• Common signs: door feels heavy, drops quickly, or sits unevenly side-to-side

• Disconnect power before servicing; for dishwashers, also shut off the water supply
• Support the door and carefully relieve spring tension before removal
• Install the new spring in the same attachment points/orientation as the original
• Replace both together to maintain even tension