Kitchenaid Valve

This water inlet valve opens and closes to control water entering your appliance. A worn or stuck valve can cause fill problems or leaks—replacing it restores proper water flow and reliable operation.

• Regulates water flow into the unit during fill cycles
• Common symptoms: no water or slow fill, water continues to fill when off, leaks from the valve body, or humming/clicking without water flow
• Typically located where the household water line connects to the appliance

• Disconnect power and shut off the water supply before servicing
• Keep a towel or container handy to catch residual water
• Note hose and wire positions; take a photo for reference and transfer any brackets as needed
• Inspect/flush the supply line and screens; reconnect and check for leaks after installation

This electrically actuated valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper fill performance and helps prevent unwanted dripping between cycles. What it does:

• Opens and closes to admit the correct amount of water at the right time
• Helps maintain stable water pressure and shutoff to the unit
• Common symptoms of a failing valve: no fill, slow/insufficient fill, water seeping into the tub when off, or leaks from the valve body
• May buzz or hum without allowing water flow when the internal coil or screen has failed or is clogged

• 1 water inlet valve

• Disconnect power and shut off the water supply before servicing
• Keep towels or a tray handy; some residual water will drain
• Note hose and wire orientations; transfer any brackets or fittings from the original valve
• After installation, restore water and power, check for leaks, and run a test fill cycle

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

This overfill control float assembly sits in the dishwasher tub and rises with the water level. It works with the float switch to shut off the inlet valve, helping prevent overfilling and potential leaks.

• Rises with the water level to engage the float switch and stop water flow
• Helps protect against tub overfill and floor leaks during the fill cycle
• Replace if the float is missing, warped, stuck, or doesn't move freely
• Symptoms can include continuous filling/overfilling, water spilling from the door, or no fill if the float is stuck in the up position

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift the old float straight up from the tub opening
• Clear any debris from the float well so the new float moves freely
• After reassembly, start a fill to ensure the float rises and water shuts off

This smart electronic valve regulates on/off flow inside the appliance under command of the control system, helping the unit fill, dispense, or operate as designed. A precise, electronically driven valve is critical for consistent performance.

• Opens and closes when energized to start or stop flow to the connected system
• Coordinates with the control board for timed, accurate operation
• Helps prevent overfill or underfill conditions
• Common symptoms of a failing valve: no fill/flow, slow or intermittent flow, continuous flow when off, leaks from the valve body, or related fill/flow error codes

• Disconnect power and shut off the appliance's supply line upstream before servicing
• Keep towels or a container handy to catch residual fluid when lines are disconnected
• Transfer connectors and any reusable brackets from the old valve to the new one, matching orientation
• After installation, restore supply and power, then check all connections for leaks and proper operation

This small filter sits inside the refrigerator's water inlet solenoid valve to trap sediment from the household water supply. Replacing a clogged or damaged filter helps protect the valve and can restore normal water dispenser and ice maker flow.

• Filters debris from the incoming water line to protect the inlet valve and water system
• Useful to replace when sediment or scale is found during valve maintenance
• Fits in the valve's inlet port to keep particles out of the valve body

• Disconnect power and shut off the water supply before servicing
• Access the rear water inlet valve, relieve line pressure, and remove the supply line
• Pull out the old filter from the valve inlet and fully seat the new filter
• Restore water, check for leaks, and purge air by running the dispenser

Fits most Kitchen Aid dishwashers. Replaces old 2 coil valves.

This single-solenoid water inlet valve controls the flow of water from your home supply into the refrigerator's water system, typically feeding the ice maker. A failing valve can stop fill, cause slow or inconsistent fills, or allow unwanted seepage.

• Opens and closes when energized to regulate water to the appliance's water circuit
• Common symptoms: no ice production, small or hollow cubes, water seeping into the ice maker, or leaks at the valve
• Electrical failure (open coil) or mineral debris can keep the valve from opening or closing properly
• Restores proper water fill and reliable shutoff when replaced

• Unplug the refrigerator and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch residual water
• Label or photograph tubing and wires for correct reassembly; cut plastic tubing square and fully seat it
• Restore water and power, then check all connections for leaks

This inlet valve controls water flow into the appliance, restoring proper fill cycles and stopping leaks when a valve fails. Replace a faulty inlet valve to regain consistent, reliable water delivery. What it does

• Opens and closes to allow water into the appliance during fill cycles.
• Replaces a valve that can cause no water, slow fill, or intermittent filling.
• Stops unwanted water flow or continuous filling when internal seals fail.
• Prevents leaks caused by a cracked or worn valve body or seals.

• Disconnect power and shut off the water supply before starting any work.
• Relieve residual water pressure and place towels or a pan to catch drips.
• Basic hand tools required; follow OEM instructions.

This gas valve controls the flow of natural gas or propane to the oven/range burner, restoring reliable ignition and steady heat for baking and broiling. Direct replacement for failed or leaking valve assemblies. What it does:

• Regulates gas flow to the oven/range burner so the burner lights and maintains temperature.
• Stops gas flow when the safety system detects a fault, preventing unsafe conditions.
• Commonly replaces valves that leak, fail to open, or prevent the oven from heating.
• Helps resolve symptoms like no bake/broil heat, intermittent ignition, or continuous clicking/try-to-light cycles.

• One gas valve assembly.

• Turn off gas supply and electrical power before attempting service; follow local codes.
• Tighten gas fittings to manufacturer torque specs and perform a leak test after installation.
• Some installations may require removing the range/oven front or burner components for access.

This solenoid valve is the electrical valve assembly that opens and closes to control fluid flow in the appliance, restoring proper fill and shutoff behavior when the original valve fails. What it does:

• Electrically opens and closes to allow or stop fluid flow to the appliance
• Stops unintended flowing or leaking when the valve seals properly
• Commonly linked to symptoms such as no fill, continuous filling, intermittent fill, or leaks near the valve
• Works as the actuator controlled by the appliance's control board to meter fluid delivery

• Disconnect power and shut off the water supply before servicing.
• Handle valve connections and seals carefully; replace any damaged gaskets or hoses.
• Reconnect wiring to the correct terminals and secure all fittings to avoid leaks.
• Test appliance through a full cycle after install and check for leaks.

A replacement gas valve that controls gas flow to the oven or range burner, restoring safe ignition and flame regulation so the appliance heats reliably. Designed to match OEM fit and restore proper gas delivery. What it does:

• Opens and closes to regulate gas flow to the burner or oven for ignition and sustained flame
• Helps resolve symptoms like no ignition, intermittent flame, or burners that won't stay lit when valve failure is confirmed
• Works with the appliance's safety and control systems to enable normal heating cycles
• Replaces a failed or leaking valve when diagnostics show the valve is the faulty component

• One gas valve

• Installation requires shutting off the gas supply and disconnecting power first; follow all local codes
• Tighten gas line connections to the manufacturer's torque specs and check for leaks with a soap solution or gas leak detector
• Verify valve part number and appliance compatibility before installation