Lg Hose Or Tube

Delivers fresh water from your home supply to your washer. Replace if cracked, leaking, worn, or damaged to restore proper fill connection.

Replacement water tube for refrigerators. Restores proper fluid routing when the original tube is cracked, leaking, or damaged. Direct fit installation.

Directs water from the valve to the ice maker fill cup. Replace this tube if it's cracked, blocked, or leaking to restore proper water flow to the mold.

The Drain Hose Assy is an OEM component specifically designed for LG dishwashers. This hose works with the drain pump to effectively drain wash water from the dishwasher tub after each cycle. 

The drain hose assy is responsible for efficiently draining wash water during and after the dishwashing cycle. It allows used water to be drained properly, keeping the dishwasher tub and components clean and dry between cycles. 

Symptoms of a bad drain hose assy include:

• Incomplete draining of wash water after cycles
• Water remaining or pooling in the bottom tub 
• Leaks or puddling near the drain pump or hose area
• Loud noises or vibrations from the drain pump

This OEM LG part is also compatible with select Sears/Kenmore.

Outlet duct for washers. Connects the washer tub to the drain pump assembly. Replace if cracked, disconnected, or leaking during drain cycles.

Connects household water supply to your washer inlet valve. Replace this hose if it's cracked, leaking, or worn to restore safe water flow during cycles.

Inlet hose connects your washer to the water supply. Replace if cracked, leaking, worn, or damaged to restore proper water flow to your machine.

Inlet hose connects your washer to the water supply. Replace if cracked, leaking, worn, or damaged to restore proper water flow to your machine.

Connects internal water lines in your dishwasher. Replace if cracked, worn, or leaking to restore a secure seal and prevent water damage under the unit.

This washer door boot gasket (bellows) seals the opening between the outer tub and the front panel on front-load machines, keeping wash water inside the drum. Replace when the seal is torn, cracked, or leaking around the door.

• Forms a flexible, watertight seal between the tub and door opening
• Helps prevent leaks during fill, wash, and spin cycles
• Typical failure signs: water on the floor at the front of the washer
• Visible rips, cracks, or warping of the boot
• Drips or seepage from the door area after a cycle

• Unplug the washer and shut off water supply before servicing
• Remove the outer and inner retaining clamps and front panel as required by your model to access the boot
• Note the boot's orientation and alignment marks; match the same orientation on the new gasket
• Ensure the gasket lip is fully seated in the grooves; reinstall clamps evenly and securely

Routes fresh water into the dishwasher during fill cycles. Replace this hose if cracked, kinked, leaking, or damaged to restore proper water flow.

Joins your washer's water line to internal plumbing with a secure, leak-resistant connection. Replace this connector if cracked, worn, or leaking.

Replace a cracked, kinked, or leaking water supply tube in your top-mount refrigerator. Installs between water line connections for ice and water.

This water guide directs water through the dispenser/ice path so water flows where it should, helping prevent leaks and misdirected dispensing. It's a small molded channel designed to route cold water inside the refrigerator. What it does:

• Guides and channels water from the supply toward the dispenser or ice-making area
• Helps prevent water from dripping into areas it shouldn't and causing puddles
• Supports consistent dispensing by keeping the water path aligned
• Commonly replaced when cracked, warped, or when water is leaking or pooling

• One water guide piece as shown

• Disconnect power and shut off the water supply before replacing
• Remove any interior shelves or panels as needed to access the guide
• Handle carefully to avoid damaging mounting tabs or adjacent seals
• Secure all clips; test dispenser and check for leaks after installation

Drain pipe for washers. Connects the pump to the drain outlet. Replace if cracked, leaking, or damaged. Essential for proper water drainage during cycles.