Maytag Gasket & Seal

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

I followed the very well made repair video for this particular part. The total time it took for the repair was under 20 minutes. But I have a suggestion for the repair video and that is to emphasize that when reinstalling boot. Have the tachnician point out that there are drain holes in the boot that need to be situated and reattached toward the bottom of the washer chassis. Unfortunately I had to redue and double the repair time because the wash water would not drain properly during wash... Read more

Did some online research and everything pointed to the fact that moisture was getting into the freezer and therefore the seal was not doing it's job. I ran my finger along the seal and sure enough I detected cold air coming out of one corner of the seal. I ordered the appropriate part from Appliance Parts Pros (APP) but decided to test my diagnosis by installing thin weather stripping in the affected area. I checked the freezer the next day and saw no accumulation of any more Rime ice so... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

I determined that the gasket was pinched, leaking at corner. Ordered new gasket from this site (easy find with part diagram). Removed old gasket, replaced with new. Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Replaced the bellow. Read more

We watched a "youtube" video on how to fix a fridge door seal and even though this particular model fridge was not the same...it helped to see how to fix it. It took me 20 minutes to remove and replace the new door seal. The part ordered was ordered and delivered next day which was great!! Read more

Purchased the gasket, but upset with myself I forgot the high temp adhesive.....a 13$ part and now 7$ for shipping. Think not for my mistake Read more

Ordered new seal pulled old one off and put new one in its place Read more

• Leaking

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

I replaced the gasket. Removing the old one was not easy. I used a razor knife to cut out most of it. And then I used rubbing alcohol to soften the remaining glue and scrapped it out with a small blade screwdriver Read more

Just like the one's I have worked on for 30 years for Whirlpool. Read more