Maytag Gasket & Seal

I searched online for replacement parts and Appliance Parts Pros had the part in stock. Before I ordered the part, I watched the video to see if I could handle the repair. I ordered the part and soaked the gaskets with warm water in the tub. The old gaskets had a much simpler setup, so no cutting was involved. I simply pulled the old gasket out of the track without issues, and installed the new one with finger pressure. Per the video, I took both doors off. However, due to the design, I could... Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Left new gasket on the table overnight so it could stretch out. Removed the door. Temporarily replaced it with plastic and tape. Pulled off old gasket. Cleaned surfaces with decreaser and wiped dry with paper towels and alcohol. Inserted new gasket. Replaced door. Read more

• Leaking

After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Started my Maytag dryer (model LDE8200ACW) with a large load early Saturday morning and immediately heard a noticeable thumping noise as the drum turned. Opened the door and checked to make sure some of the laundry hadn’t wadded up and was causing the thumping. Restarted it but the thumping was still present. Did a google search for obvious possible causes for the symptoms but the only suggestion that made sense was to check and make sure the dryer wasn’t rocking on its feet. Checked and found... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

New door seal did the trick. Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

• Will not tumble

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

By replacing it Read more

Purchase a new one and installed per your video on Youtube. Great and easy. Read more

Ordered and replaced bellow. It is important to supply the correct model number as my machine is a later model than the one used in the training video. The front panel is one piece, rather than two. Additionally, several of the fasteners were hex head screws, rather than torks. The Bellow is somewhat different having an opening for the light fixture. That said, the video was adequate to get the general idea of how to remove and replace the bellow. I found it very difficult to replace... Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more