Maytag Switch

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

This surface burner ignitor switch mounts on the gas valve and signals the spark module when you turn the knob to Lite. Replacing a faulty switch restores reliable clicking and ignition on the affected burner. What it does:

• Closes the circuit to send power to the spark module when a knob is turned
• Helps produce a steady spark at the electrode for quick burner lighting
• Common symptoms it may address: no spark on one burner, constant clicking with knobs off, or intermittent sparking
• Used on gas cooktops/ranges that employ one spark switch per burner valve

• 1 ignitor switch

• Disconnect power and shut off gas before servicing
• Remove the knob and access the control area to reach the switch on the valve stem
• Note wire positions; transfer wires to the new switch and align it correctly on the valve
• Reassemble, restore power/gas, and test for proper spark operation

This rotary, 3-position temperature selector switch lets you choose the cycle's temperature. When it wears out, settings may not respond or temperatures may be wrong. Replacing it restores accurate temperature selection and dependable performance.

• Provides user control of temperature with three selectable positions
• Sends the chosen setting to the appliance's control system to achieve the requested temperature
• Common signs of failure: only one setting works, temperature doesn't match the selection, or the selector is loose/hard to turn
• Visible damage to the switch shaft or terminals

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/console
• Note wire locations and transfer them one-by-one (or take a photo for reference)
• Reinstall the existing knob, aligning the flat on the shaft as removed

This Marquardt ground switch completes the appliance's ground connection so controls and safety systems have a proper reference. Replace a failed ground switch to restore reliable grounding and help eliminate related electrical faults. What it does:

• Provides the ground connection path used by controls and safety circuits.
• Replaced when continuity tests fail or when appliances have intermittent power, control errors, or nuisance breaker trips.
• Restores correct electrical grounding to help reduce fault conditions and erratic control behavior.
• Matches the original switch form and electrical connector layout for a direct replacement.

• Disconnect all power (unplug appliance and/or shut off breaker) before beginning service.
• Photograph or label wiring and connector positions before removal; transfer connectors to the new switch exactly.
• Inspect connectors and wiring for damage; replace any frayed or heat-damaged wiring.

This replacement switch restores reliable on/off control for the matched function in your appliance. A worn or sticking switch can prevent components from powering correctly; replacing it helps bring back consistent, safe operation.

• Opens and closes an electrical circuit to control a specific component
• Actuates via a knob, button, lever, or door/lid mechanism
• Common symptoms: unit or component won't start/turn on, intermittent operation, or must press/hold to work
• Visual clues: loose actuator, heat discoloration, or burned terminals

• Disconnect power before servicing; verify no voltage with a meter
• Document wire positions; move leads to the new switch one at a time
• Secure the switch in the original orientation and ensure proper actuator alignment
• Restore power and test the controlled function for proper operation

This water level pressure switch senses tub water level through the air hose and signals the control when to stop filling at the selected setting. It helps prevent overfilling and ensures proper wash and rinse performance.

• Monitors water level via internal diaphragm and air-tube pressure
• Signals the control/timer to open or close the inlet valves at the chosen level
• Allows the cycle to advance once the correct fill is reached
• Common failure symptoms include overfilling, underfilling, continuous filling, or cycle stalling while waiting to fill

• Disconnect power and turn off water supply before servicing
• Access the console; move wire connectors and the pressure hose to the new switch one at a time
• Inspect the pressure hose for cracks, kinks, or leaks; seat it fully on the switch port
• Run a quick fill test to ensure water stops at the selected level before reassembly

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

2 position. Extra rinse.

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This switch/wire lead assembly is used on select ranges and wall ovens to control a specific function. Replacing a worn switch restores positive on/off control and reliable power flow through the attached leads. What it does:

• Opens or closes the circuit for the assigned feature when actuated
• Routes power through the attached leads to the controlled component
• Symptoms can include: feature won't start, won't turn off, intermittent operation, or heat-discolored/burned terminals or wires
• May feel loose or fail to click/hold position compared to normal operation

• One switch with attached wire leads

• Disconnect power at the breaker before servicing
• Access the control panel or mounting area; note wire locations (take a photo for reference)
• Transfer wires one at a time to the new switch; reuse original mounting hardware
• Restore power and test the function before final reassembly

Color: Black. Instruction sheet included.

This water level pressure switch monitors the tub's water level via an air hose and signals the washer when to stop filling and move to the next step. Replacing a failed switch restores accurate fills and reliable cycle operation.

• Senses tub water level through air pressure and communicates with the timer/control
• Shuts off inlet valves at the correct level to help prevent overfilling
• Allows the cycle to advance to wash, drain, and spin based on sensed level
• Common symptoms: overfilling/overflow, underfilling or no fill, cycle stuck at fill/sensing, no agitate or spin

• Disconnect power and turn off water supply before servicing
• Access the control console to remove the old switch; note wire locations for correct transfer
• Move the air hose to the new switch and ensure the hose is clear, undamaged, and snug at both ends
• Reassemble and run a test fill to verify proper shutoff and cycle progression

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks

Color: White

This infinite surface element switch controls the heat output of a cooktop/range element. Replacing a worn switch restores smooth, reliable temperature adjustment for the designated Flex element, preventing issues like stuck-on-high heat, no heat, or erratic cycling.

• Regulates power to the surface element by cycling on and off at the selected setting
• Dedicated control for the unit's Flex element circuit
• Common failure symptoms: element won't heat, only heats on high, won't shut off, or heats inconsistently

• Disconnect power at the breaker before servicing to avoid electrical shock
• Pull the control knob straight off; access the switch from the control panel and note its orientation
• Label and transfer wires one at a time to matching terminals on the new switch
• Reassemble, restore power, and test all heat settings for proper operation

Restore precise cycle selection with this rotary encoder cycle switch. Mounted behind the control knob, it sends your chosen setting to the washer's control, resolving unresponsive or erratic knob behavior so the correct cycle and indicators engage.

• Translates knob rotation into signals the main control uses to select a wash cycle
• Helps ensure the selected cycle registers accurately on the user interface
• Wear or internal faults may cause an unresponsive or erratic cycle knob
• May also lead to incorrect indicator lights, intermittent selection, or a no-start condition

• Disconnect power before servicing
• Pull the knob straight off; open the console to access the encoder
• Release locking tabs and transfer wiring one connector at a time; align the keyed shaft
• Reassemble and verify the indicators respond to knob rotation before running a load