Need Help?
Call
New seals come with this valve.
Opened the washer (details later) and noted the controls and water path. Ordered dispenser bottom and cover and dispenser valve assembly and rubber washers. When the parts arrived I removed the top portion of the detergent dispenser assembly; removed the door and 2 screws from opposite door wall; snap open the front cover and lifted it off; removed 1 metal screw each from the bottom front corners of the top cover; lifted the top cover and used a piece of wood to hold it up; pull... Read more
Usually ships within 4 - 14 days
If your burner won't ignite, won't shut off, or the knob feels loose, the top burner valve likely needs replacement. Moderate DIY repair in 1-2 hours.
Removed burners, grates, removed cook top,took screws out from raised trim and wells for burners. Removed electric connection for burner igniters and took gas connection off of valve that goes to burners. Took out screw that holds in gas valve in gas manifold. Replaced gas connections to burners on new valves, installed new valves and trim . Read more
Fix washer that won't fill, shows OE/NF error, or keeps running water even when off. Cold water inlet valve replacement takes 5-10 minutes with basic tools.
After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more
If your dishwasher shuts off mid-cycle or leaks water, a warped or stuck overfill float may be the cause. This 5-minute fix restores proper fill control.
Replace the motherboard and used YouTube to replace float switch. Part ordered was exactly what I needed Read more
This replacement water inlet valve controls the flow of water to the appliance's dispenser and ice-making components, restoring normal fill and preventing supply interruptions when a valve fails. What it does
Thanks to Appliance Parts Pros® I was able to replace that old water valve drip with a new valve. Simply unplug power cord, turn off water, disconnect hoses from machine, with front off machine and top unscrewed, tilt top back and unplug wires to old valve remove screws holding valve from back of machine, remove small hose from old valve to top ring and replace if worn. Then just attach wire harness to new valve, screw valve to back using old screws (2), attach hose to top ring, close top of... Read more
Fix gas smell or burner ignition issues with this range top burner valve. Common repair for leaking gas odor when range is off. Moderate difficulty.
I replaced the Igniter switch, two control valves and one holder/orifice (because I couldn't get the screws out and decided to just replace it rather than re-tape it and get new screws). The one thing I forgot was I have propane and the orifice was for natural gas. Fortunately, I was able to swap out the orifice from the old holder. Read more
No water or ice? Secondary water valve controls flow to dispensers and ice makers. Common fix for no dispensing, leaks, or ice maker failure.
Replaced primary inlet water valve and secondary water valve. Read more
Fix your refrigerator not filling with water or overfilling with this water inlet valve. Controls water flow during fill cycles. Easy DIY repair.
This is a gas surface burner valve that controls the flow of gas to a cooktop burner. It connects to the burner control knob and regulates flame size from high to low settings. Replace this valve if a burner won't light, has an uneven flame, won't turn off, or if you detect a gas smell when the knob is in the off position.
I'm not an appliance repairman. Luckily this repair was easy to identify and only took about 20 minutes to complete. Removed the knobs and the screws holding the knob plate. unscrewed the burner valve and swapped out with the new part from appliancepartspros. Best part: the part was $34 compared to another site's $93 ( or $83 if you mentioned a competitor site). Read more
Burner won't ignite or flame is too high or low? This range top burner valve controls gas flow to surface burners. Moderate DIY repair.
Fix a burner that won't ignite, stays on high, or won't adjust with this cooktop burner valve. Common repair for gas flow control issues on cooktops.
Fix a cooktop burner that won't light, won't adjust temperature, or has weak flames with this burner valve. Moderate difficulty repair for gas cooktops.
Fix a burner that won't light, won't adjust, or stays on with this cooktop burner valve. Controls gas flow to individual burners. Moderate DIY repair.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.